The Mass Casting is a recent method developed in Europe to produce mold with ease and less time.
铸件的质量是近年来开发的方法在欧洲的生产模具，其方便与更少的时间。
The self-compensated contraction caused by graphite dilatation in the solidification process of nodular cast iron makes casting with less flow-off or casting without flow-off possible.
利用球墨铸铁凝固过程中的石墨化膨胀，进行自身补缩，可以实现少胃口或无冒口铸造。
Since the fight went live, there has been a hidden protection for players that prevents the casting of Psychosis and Malady of the Mind on targets with less than 30 Sanity.
当战斗开始后，将对玩家产生一种隐藏性保护，防止30心智以下的玩家受到失神及心灵缺陷攻击。
It is simple process, less pollution, low cost, good quality casting, and can meet producing of locomotive casting, that the investment pattern was made from the shell mold was made from silica sol.
采用硅溶胶粘结剂制造型壳，工艺简单，污染少，成本低，铸件质量好，满足机车类精铸件生产要求。
As compared with static casting, above mentioned technique can improve yield and mechanical properties of castings significantly and provide sound castings at less cost.
与重力铸造相比，该工艺显著地提高了铸件成品率和机械性能，达到以较少的成本生产出较多优质铸件的目标。
Avoid the quick changes of casting structure, use fillet radius on internal Angle when possible, which is no less than R0.3.
铸件结构应避免急剧变化，尽可能避免尖角，圆角应达到R0.3以上。
Wax precision casting is adopted for the shaft sleeve, increasing material utilization ratio by 77% and realizing "less cutting and no cutting".
铸造工艺采用石蜡精铸成型，使材料利用率提高77％，达到少切削、不切削目的；
By rule of thumb, the total thickness of pad and casting (at the pad location) should not be less than one-fifth of the metal-feeding distance.
由经验法则，其总厚度的软垫及铸造(在垫板上的位置)，应不低于上就有五分之一的金属补缩距离。
It shows that thin slab continuous casting has a greater secondary cooling intensity, a faster solidifying rate, a fine and uniform structure and less segregation than conventional slab casting.
研究表明，薄板坯的二冷强度大，凝固速度快，组织细小、均匀，其内部溶质元素的偏析程度远低于传统连铸板坯。
After casting a spell any subsequent spellcasts will cost 10% less for 5 seconds. This ability stacks up to 5 times.
每释放一次技能，下一次的法术消耗减少10%，持续5秒，最多叠加5次。
Hand sculpting offers the greatest opportunity for creativity and usually costs less than casting.
手工雕刻的创造力提供了最大的机会，通常成本比铸造低。
Under the continuous condition of wind blowing and sunlight casting, water flow appears to reduce less.
然而对水流言，在风及阳光等持续地吹，持续地照射下，水量似乎没有明显的减少。
The less gas volume may be used while the higher casting velocity conditions or smaller slab size.
实际吹氩量标准大断面临界吹氩量可稍大，同样断面条件下，高拉速吹气量设置小而低拉速大。
The less gas volume may be used while the higher casting velocity conditions or smaller slab size.
实际吹氩量标准大断面临界吹氩量可稍大，同样断面条件下，高拉速吹气量设置小而低拉速大。
应用推荐