Fretting fatigue usually occurs in lap joints of aircraft structure.
搭接件是飞机结构中容易产生微动疲劳损伤的部位。
Therefore, the user presses the length of lap joints to determine the number of curing machine units.
因此，请用户按接头的搭接长度，确定硫化机的台数。
The effect of the recessing on the strength and stress distribution of adhesively bonded single-lap joints is discussed.
研究单搭接接头胶缝中预留间隙对接头拉剪强度和应力分布的影响。
Welding and allied processes. resistance spot, projection and seam welded lap joints. classification of defects with explanatory comments.
焊接和有关技术。电阻点焊凸焊或缝焊搭接接头。带解释的缺陷分类。
The influence of embedded trilateral cross-section metal bar in the fillet on the strength and stress distribution of single lap joints was discussed.
研究了在胶瘤中嵌入三角形金属楔块对单搭接接头强度和应力分布的影响，结果表明，金属楔块能显著提高接头的强度。
Microstructure characteristics and mechanical properties of lap joints were researched by SEM, EPMA, EDS, micro-hardness tester and tensile experiment machine.
通过SEM、EPMA、EDS、显微硬度计和拉伸实验机对搭接接头的微观组织及力学性能进行了研究。
Based on the hardness analyses of actual spot welded joints, a computational model that consists of nugget, HAZ and base metal is established for the single point spot welded lap joints.
基于对实际点焊接头硬度分布的分析，建立了包括熔核、热影响区和母材的单点点焊搭接接头计算模型。
The resistance brazing principle; the selection of brazing parameters and quality control measures are introduced for the lap joints of copper strip rotor coils within big electrical generator.
介绍了大电机紫铜带线圈斜搭接接头电阻钎焊装置工作原理、参数选择以及钎焊质量的控制。
The stress distribution of continuous and recessed bonding single-lap joints is discussed with use of elastoplastic finite element method (FEM) and experiment, considering the effect of fillet.
运用弹塑性有限元法结合实验研究了连续和间隙连接的单搭接接头应力分布规律，并考虑了胶瘤的影响。
The influence of fillers in epoxy adhesives with different magnetic characteristic is investigated through exposure the single lap joints to magnetic field using the device made by authors ourselves.
采用自制的装置研究了在环氧胶中加入不同磁特性的填料后，对经磁场处理钢-环氧胶接头剪切强度的影响。
The influence of length and position of recessing on the strength of adhesively bonded joints with different single-lap length was presented.
研究了间隙长度和间隙位置对不同单搭接接头强度的影响。
The maximum shear strength of welded joints can be increased by optimizing the form of lap welding.
通过优化搭接焊形式能提高焊接接头的最大剪切力。
When diameter and thickness of lap brace became smaller, the ultimate capacity of both CW and TW type overlapped joints decreased compared with symmetrical overlapped joints.
当搭接腹杆直径变小、壁厚变薄后，CW和唧型搭接节点极限承载力均相对对称节点下降。
The most commonly used joint configurations are the lap, scarf, and butt joints.
最常用的连接结构是搭接，嵌接和平接。
The most commonly used joint configurations are the lap, scarf, and butt joints.
最常用的连接结构是搭接，嵌接和平接。
应用推荐