Keyway slot for tooling location.
键槽插槽工具的位置。
The lock body includes a keyway disposed on an outer surface.
该锁具本体包括置于外表面上的钥孔。
A lock assembly includes a lock body and a keyway covering member.
一种锁具组件包括锁具本体和钥孔覆盖部件。
Rod - ends with self - aligning ball bearings. long threaded shank and keyway. dimensions and loads.
带自位球轴承的杆端。长螺纹杆和键槽。尺寸和负荷。
Features free-spinning keyway to prevent wrench attacks, but easy to turn when correct code is entered.
功能特点免费纺键槽，以防止扳手对锁面的破坏，但拥有正确的代码，进入屋子是十分的方便。
Rod - ends with self - aligning ball bearings. long threaded shank without keyway. dimensions and loads.
带自位球轴承的杆端。无键槽的长螺纹杆。尺寸和负荷。
The toolholder is used for outer slotting and the tool bar for inner slotting and for slotting the keyway.
机床附有电磁自动抬刀的刀架和刀杆。刀架用天外插削， 刀杆用于内插削和插键槽。
This particular failure was accelerated by the sharp corners that had been cut in the shaft's rectangular keyway.
这个出格地掉败是加快由急弯时说，已被削减，在轴地矩形键槽。
The stress in floor plate with keyway are more than it with straight seam under the same level of uplift pressure.
同级扬压力作用下，带键槽底板块的应力大于直缝底板块的应力；
Improvement is made to the positioning feller gauge in flywheel keyway broaching machine by V-type auto center align.
利用V型块自动对中定位原理，对飞轮键槽拉床定位塞尺进行改进。
The system includes the electronic cylinder that has no keyway to pick and the electronic key that cannot be duplicated.
此系统包含电子柱体，电子柱体没有锁眼，所以不能被复配。
This paper discusses the cause of keyway symmetry error produced and test method and approaches to related calculating formulae.
论述了键槽对称度误差的产生原因以及检测方法，并对有关计算公式进行了探讨。
Pointing to the accuracy requirement of the keyway on shifts, this paper presents a special jig and a cutter positioning method.
针对轴类零件键槽精度的要求，介绍了一种专用夹具及对刀方法。
The processed products for large tankers rudder device keyway, Can also be used for large-scale structure of the processing keyway .
本文设计的机床为加工大型油轮舵装置键槽的机床，也可用于大型结构件键槽的加工。
Lastly during assembly care is taken to avoid damaging the seals when passing over the keyway or performing bearing surfaces of the shaft.
最后，在组装过程中，当部件通过键槽时，注意避免损坏密封和轴的轴颈表面。
This is a presentation of the keyway installation of the rudder processing and for the processing and design of the keyway dedicated machine.
本文研究了该舵装置键槽的加工工艺以及为加工键槽而设计的专用机床。
Milling cutter series: straight shank milling cutter, straight shank keyway milling cutter, prick milling cutter, nonstandard milling cutter.
铣刀系列：直柄铣刀、直柄键槽铣刀、锥度铣刀以及其它非标铣刀。
The paper prov rides a practical method of measuring and assessing the symmetrical error of the keyway in production and data processing formula.
本文提供了生产中实用的键槽对称度误差检测方法和数据处理公式。
When the keyway covering member is in the covering orientation, a covering portion of the keyway covering member aligns with the keyway to cover the keyway.
当该钥孔覆盖部件位于该覆盖方位中时，该钥孔覆盖部件的覆盖部分与该钥孔相对准以覆盖该钥孔。
The more and concentrate stress in the keyway are produced, however, this condition does not occur in the straight seam way. Both of them meet the stress requirements.
带键槽底板块在键槽处产生较大应力集中，而直缝情况则没有产生较大应力集中，两者均满足应力要求。
The new method for machining keyway in holes and the special tool is presented, with which the keyway not only in blind holes but also in shoulder holes can be machined.
介绍了一种加工孔内键槽的新方法和相应的专用工具。不但可用来加工通孔内的键槽，而且还能用来加工盲孔内的键槽或有障碍台肩的孔内键槽等。
The rudder device keyway to hole keyway , Hole of the conical hole, Not run through the holes, Moreover structure of two key connection , Large size , High precision machining.
舵装置的键槽是内孔键槽，孔为锥孔、盲孔，而且采用双键联接结构，尺寸大，加工精度较高。
The unique locking bar system prevents the key on the output shaft from tipping in the keyway, eliminating the possibility for key and keyway damage that results in a loss of productivity.
独特的锁闭杆系统，防止输出轴上的键在键槽倾斜，消除了键和键槽损害的可能性及其可能会导致的生产力损失。
The unique locking bar system prevents the key on the output shaft from tipping in the keyway, eliminating the possibility for key and keyway damage that results in a loss of productivity.
独特的锁闭杆系统，防止输出轴上的键在键槽倾斜，消除了键和键槽损害的可能性及其可能会导致的生产力损失。
应用推荐