Based on the applied project, problems of the oil drill tube joint detection are solved step by step. Finally, automatic and effective joint measurement method is realized.
论文从实际的工程项目出发，逐一解决了接头检测存在的难点，最终实现了钻杆接头的自动、高效检测。
Keen joint injury of female hockey athletes were investigated in Guangdong provincial team and the isokinetic measurement was taken to analyze the reason of injury.
对广东女子曲棍球队运动员膝关节损伤进行了调查，结合等动力量测试对女子曲棍球运动员膝关节损伤的原因进行了分析。
Based on the results of the measurement and the analysis of biomechanical mechanism of the ankle injury, 16 patients with trimalleolar fractures and subluxation of the ankle joint were treated.
根据解剖测量及踝关节损伤生物力学机制分析结果，对16例三踝骨折伴踝关节半脱位的患者进行治疗。
A static reference measurement is taken to avoid the effect of big skin deformation around joints to the measured data of joint markers.
并提出静态参考测量的措施，避免关节周围较大的皮肤变形对测量数据的影响。
In the measurement of human upper limb, the position for the center of shoulder joint can be supposed by comparative position to acromion.
在人体测量中，肩关节中心的位置要通过其与肩峰的位置关系进行估测。
The extraction of feature lines for shoe instep surface curve was realized by joint-type measurement arm in Coordinate measurement in shoe instep.
鞋楦坐标测量采用关节式测量手臂实现鞋楦曲面特征线的提取。
This paper investigates the measurement principle and model of a parallel dual-joint coordinate measuring machine (PD-CMM) which has three degrees of freedom (DOF).
该文探讨了一种三自由度(DOF)平行双关节坐标测量机的测量原理和测量模型。
The small blind hole method is used for the measurement of residual stress inside T joint.
采用盲孔法测定了丁字焊缝的残余应力。
The techniques detail measurement of both joint range of motion and muscle length testing of the spine and extremities using the goniometer, the inclinometer, and the tape measure.
这些技术具体到如何通过量角器、测斜仪和卷尺来测量脊髓和手足部的关节活动度和肌肉长度。
The system of measurement is composed by joint, spring pipe, and power transmission setting, and use the needle to note the number.
仪表的测量系统由接头、弹簧管和传动机构组成。通过指针指示仪表读数。
Moreover, an experimental method of touch pin measurement to analysis solder joint shapes was put forward, the results show the calculating results and the experimental results were identical well.
提出了一种用触针测量法研究焊点三维形态的实验方法，并对计算结果和实验结果进行了比较，结果表明，计算结果与实验结果吻合良好。
Therefore, the research on joint offence and the identity relation is quite significant for determining the kind of crime and the measurement of penalty.
因此，研究共同犯罪与身份的关系，对于共同犯罪的定性与量刑具有十分重要的意义。
The fiber Bragg grating used for simultaneous measurement of strain and temperature was written on the joint of two different fibers, and has two reflection peaks at different wavelength.
用于同时传感温度与应变的光纤光栅写于两种不同光纤的连接处，本身具有两个反射峰。
The distances between the bony landmarks and joint line are also measured. The results of this study suggest that 3D conceptual measurement can reduce the errors from 2D images measurement.
研究结果显示，本研究突破以往用二维影像的测量来代表三维空间的距离及角度，避免以往因单张影像测量所造成的误差。
The article introduces, as taking the measurement of sticking cracking-resistant adhesive tape at the joint between GRC boards, the cracks of the wall have been prevented effectively.
本文采用在GRC轻板的接缝处粘贴防裂带的措施有效地解决了墙体开裂。
The vibration transmission properties of joint beams were investigated by measurement.
对多种连接形式的连接梁进行了振动传递特性的试验研究。
An improved four-parameter DH model is used to deduce the double parallel-joint CMM measurement model. Error model of the double parallel-joint CMM is discussed based on the measurement model.
文中利用改进四参数DH模型导出平行双关节坐标测量机的测量模型，在此基础上建立该坐标测量机的误差模型。
Different ways of erosion measurement were also compared with each other and the T-type joint method is the best one.
比较了几种测定熔蚀的方法，其中以丁字接头为最好。
The traditional measurement is completed by a multiple-site joint way.
传统的光学测量方法是采取多站交汇方法完成测量。
The results of measurement show that, the residual stress was eliminated well in near all of the measured points. and that it did not eliminate well in some points of the last welded joint.
测试结果表明，大部分测点的残余应力均得到了较好的消除，但最后一道焊缝的一些测点焊接残余应力消除效果较差。
Aiming at the 3-d laser measurement system and the joint-type measurement system, the paper put forward the technology of tracking measurement based on pre-scanning and signal separately.
并针对三维激光测量系统和关节式测量系统，分别提出了预扫描的随动测量技术和信号跟踪算法的随动测量技术。
Aiming at the 3-d laser measurement system and the joint-type measurement system, the paper put forward the technology of tracking measurement based on pre-scanning and signal separately.
并针对三维激光测量系统和关节式测量系统，分别提出了预扫描的随动测量技术和信号跟踪算法的随动测量技术。
应用推荐