In order to solve Audi car muffler welding problems, a MIG automatic welding process and equipment arc developed which is suitable for the material, structure and joint type of the muffler.
针对奥迪轿车消音器的材料、结构及接头形式，研制了适用于消音器焊接的熔化极气体保护自动焊设备，并对焊接工艺进行了研究。
In Cartesian space, linear trajectories and arc trajectories are discussed deeply. Then the advantages and disadvantages of trajectories in joint space and Cartesian space are compared.
在笛卡尔空间的轨迹规划则深入讨论了直线函数插值和圆弧插值，然后对笛卡尔空间与关节空间轨迹规划的优缺点进行了比较。
English Name:Welding and allied processes - Recommendations for joint preparation - Manual metal-arc welding, gas-shielded metal-arc welding, gas welding, TIG welding and beam welding of steels.
简体中文标题：焊接和相关工艺。接缝制备的建议。钢的手动金属电弧焊、气体保护金属电弧焊、气焊、TIG焊接和束焊。
Distinctive modelling design according to the design of principle of human body engineering arc shape, can perfect joint your waist, give your body good support.
独特的造型设计根据人体工程学原理设计弧线形状，能完美的贴合您的腰部，给予您的身体良好的支撑。
By comparing backgouging of plasma arc with carbon arc to the welded joint of 13-5 martensitic stainless steel, the backgouging of plasma arc is proved feasible for the full penetration weld.
通过对13 -5型马氏体不锈钢焊接接头进行等离子弧清根及碳弧气刨清根的比较，证明等离子弧清根对全焊透焊缝实施背面清根是可行的。
Studied the joint rigidity which affects deformation characteristics of prefabricated arc board of freezing well.
研究了影响冻结井预制弧板井壁变形特性的接头刚度。
In this paper, the method measuring joint reduction ratio of V01 arc welding robot is presented.
提出了V01弧焊机器人关节减速比的测量方法。
The dangerous position are adjacent the centre of the outside and external circular arc surfaces of wave-valley or of external circular arc surfaces of wave-hump at the expansion joint.
再沸器膨胀节的危险截面在波谷、波峰圆弧中点附近，危险点在波谷圆弧中点附近内、外表面和波峰圆弧中点附近内表面处。
The tests show: there are steady arc burning, fully fused weld joints, good connection between base metal and weld joint, no air bubble, cracks etc.
试验过程电弧燃烧稳定，焊接接头充分熔透，母材与焊缝连接良好，未见气孔、裂纹等缺陷。
The forces acted on melting pool during plasma arc welding process are analyzed. The violent movement of liquid metal is as the result of joint forces acted on the pool.
通过对等离子弧焊接时熔池的受力情况分析，阐明了液体金属剧烈运动是由于多种力共同作用的结果。
The influence of He-to-Ar ratio in AC-TIG on the AZ31 welding properties was studied. The arc characters, weld penetration, joint forming were measured and analyzed.
探讨了氦气和氩气不同配比对AZ31 镁合金交流钨极惰性气体保护焊（TIG）焊接性的影响，对不同气体配比的混合气体电弧特性、熔深、焊缝成型进行了分析和测定。
The microstructure and properties of welded joint of EH40 grade ship steel plate by submerged-arc welding process were analyzed.
对EH40船板钢埋弧焊焊接接头的组织性能进行了试验分析。
To solve the problem, the welding joint construction was re-designed and argon-arc welding was employed.
解决措施为采用氩弧焊，改进焊接结构设计等。
The national standard is suitable for welded joint of carbon steel and low alloy steel with gas welding (being used for sheet metal), manual arc welding and gas - shielded welding.
本标准适用于气焊(用于薄板)，手工电弧焊及气体保护焊焊接的碳钢、低合金钢焊接接头。
In this paper the Submerged Arc Welding procedures for Q420E butt joint of Songhua River Stayed-cable Bridge were investigated.
对松花江斜拉大桥钢梁用q 42 0e厚板对接接头的埋弧焊焊接工艺进行了研究。
The results show that after TIG arc remelting treatment, the T-joint weld toe area can improve the shape of the weld toe, however, the area till shows a tensile residual stress state.
数值计算结果表明：T型接头焊趾区经过TIG电弧重熔处理后，虽然能够改善焊趾的形状，但该部位仍呈拉伸残余应力状态。
The joint microstructure and mechanical properties of high strength bainitic steel plate were studied by CO2 gas shielded welding(CGSW), submerged arc welding(SAW) and manual arc welding(MAW).
利用二氧化碳保护焊、埋弧焊、手工电弧焊研究了高强度贝氏体钢板焊接接头的组织和力学性能。
The joint microstructure and mechanical properties of high strength bainitic steel plate were studied by CO2 gas shielded welding(CGSW), submerged arc welding(SAW) and manual arc welding(MAW).
利用二氧化碳保护焊、埋弧焊、手工电弧焊研究了高强度贝氏体钢板焊接接头的组织和力学性能。
应用推荐