Why is RB interrupt routine running twice?
为什么RB中断程序运行两次?
Your interrupt routine does a little bit of work, schedules a DPC, and returns.
你的中断程序完成一些工作,确定一个延迟程序调用(的时间),并返回。
The entire control algorithm is implemented as a separate module within this interrupt routine.
整个控制算法被实施作为一个分开的模块在这个中断惯例之内。
But what happens if the interrupt routine executes in the same processor as the code that took out the lock originally?
但是如果运行在同一个处理器中的中断例程取得了先前的锁会发生什么呢?
This article helps device driver developers test the interrupt service routine as much as possible by simulating the various interrupts.
本文通过模拟各种中断,尽可能地帮助设备驱动程序开发人员测试中断服务例程。
By default, the driver IRQ routine should return IRQ_HANDLED as it is a bug to return IRQ_NONE when the driver has actually handled that interrupt.
缺省情况下,驱动程序IR Q例程应该返回IRQ_HANDLED,当驱动程序正在处理那个中断时却返回了IRQ_NONE,说明存在bug。
The Orinoco interrupt service routine populates sk_buffs with data received from the WLAN and passes it on to the IP stack via netif_rx.
orinoco中断服务例程用从WLAN接收的数据填充sk _ buffs,并经由netif_rx将它传送到ip栈。
The address of an interrupt service routine.
中断服务程序所在的地址。
If you regularly attend club meetings, church, or other activities, try not to interrupt your routine just for bad weather.
如果你总是按时参与俱乐部聚会,按时去教堂,按时参加集体活动,就一定要继续坚持下去,不要因为糟糕的天气而中断。
Kprobes provides an interface to break into any kernel routine and collect information non-disruptively from the interrupt handler.
Kprobes提供了一个强行进入任何内核例程并从中断处理器无干扰地收集信息的接口。
If the restart flag is set to True (the default), then an interrupt to the routine caused from some UNIX signal will cause a restart of the routine.
如果restart标志设置为True(默认设置),那么在某些UNIX信号造成中断时,会重新启动例程。
If the girls go talking on too long, don't be afraid to just interrupt them and launch into the next routine.
假如女孩开始长时间谈话,别怕,直接打断他,然后开始下一个惯例。
Isr interrupt service routine. code that performs actions necessary to deal with the condition that caused the interrupt.
中断服务程序。在执行操作时处理可能引起中断情况的代码。
When an interrupt occurs the current state of the processor is saved and an interrupt service routine is executed.
当一个中断发生,当前的处理器状态被保存并且中断服务程序开始运行。
When an interrupt occurs, the current state of the processor is saved and an interrupt service routine is executed.
当一个中断发生,当前的处理器状态被保存并且中断服务程序开始运行。
When the interrupt service routine exits, control of the processor is returned to whatever part of the software was previously running.
当中断服务程序退出,对处理器的控制权转到先前运行的那个软件上。
On software, we take full advantage of the low power modes of the MCU to finish the task in ISR (interrupt service routine), so, the power of system rest with the ISR executive time.
在软件设计上,充分利用所选单片机的低功耗模式,让检测任务在中断服务程序中完成,使系统的功耗主要取决于中断服务程序执行的时间。
At last, in the section of software design, startup code programming, operating system choosing and transplanting, task design, drivers design and interrupt service routine design had been discussed.
最后,在软件设计部分探讨了启动代码编写、操作系统的选择和移植、任务规划和设计、驱动程序设计以及中断服务程序设计。
NET system architecture, and describes the interrupt principle. In order to install the interrupt service routine, we present the way to modify the kernel and the OAL.
NET的系统结构,并详细阐述其中断原理,介绍如何修改内核和硬件抽象层安装中断服务例程。
PL/M-96 program language is used as the software of the controller. The signal frequencies are distinguished and the persistence time of the frequency is accumulated with interrupt process routine.
数字化控制器控制软件采用PL/M-96高级语言编程,其中断处理程序用于辩别信号频率、累计每一频率持续时间。
In most RTOS, the timer interrupt service routine (ISR) executes at every time tick.
在一般的嵌入式实时操作系统中,时钟中断服务程序在每个时钟节拍工作。
Code generated for Silicon Labs single-cell C80519XXF by a non-OCG compiler results in an average of 108 cycles to execute the interrupt service routine and main loop overhead for each sample of data.
非ocg编译器针对SiliconLabs单电池供电c 80519 XXF所产生的代码,每次数据采样平均会有108个周期来执行中断服务程序和主循环。
Aim Objective: to master the timer T0, T1 of the mode selection and programming methods, to understand the design method of the interrupt service routine, and learn skills in real-time debugging.
实验目的目的:掌握定时器t0、T1的方式选择和编程方法,了解中断服务程序的设计方法,学会实时程序的调试技巧。
The contents of the interrupt service routine: all the lights off, 2 seconds later all the light-emitting diode, another 1 second to return after the break.
中断服务子程序内容:灯全部熄灭,2秒钟后发光二极管全部点亮,再过1秒钟后中断返回。
The design of digital control system includes DSP interrupt service routine and CPLD logic control.
数字控制系统软件设计,包括DSP中断服务子程序和CPLD逻辑控制。
When the interrupt service routine exits control of the processor is returned to whatever part of the software was previously running.
当中断服务程序退出,对处理器的控制权转到先前运行的那个软件上。
Software design is divided into two parts, the main program and interrupt service routine.
软件设计分为两块,主程序和中断子程序。
Software design is divided into two parts, the main program and interrupt service routine.
软件设计分为两块,主程序和中断子程序。
应用推荐