Hot cracks commonly occurred in inside weld as the forming process of SSAW pipe.
螺旋埋弧焊管在成型过程中容易产生内焊热裂纹。
Inside weld produced cracks are often faced problem by adopting wide coil with small forming Angle to produce small size spiral submerged welded pipe.
采用宽板小成型角生产小口径螺旋缝埋弧焊钢管时，内焊缝产生裂纹是经常遇到的问题。
Through analysis on inside weld forming and welding procedure of SSAW pipe, it pointed out weld crack is easy to appear in brittle temperature zone in welding pool.
通过对螺旋埋弧焊管内焊缝成型和焊接过程的分析，指出焊缝裂纹易产生在焊接熔池脆性温度区。
The longitudinal cracks along bond line and the transverse cracks which cut across the weld metal cross section inside weld metal were formed, while X65 pipe line steel was welding.
X65管线钢在焊接过程中，内侧焊缝金属出现横向和纵向沿熔合线方向的裂纹，横向裂纹贯穿焊缝金属横截面。
Inside the gated compound, workers in tarred jerseys and goggles weld and drive screws. Back in New York, Rino's shares are frozen at 40 cents.
在复合大门里，工人们穿着涂球衣，戴着焊接护目镜，旋入螺钉。回到纽约，绿诺科技的股票冻结在40美分上。
On overall inspection of interior and exterior of pre-hydrogenating reactor of Shanghai Oil Refinery Factory, large cracks was found on the surface of weld and inside of the weld.
在上海炼油厂预加氢反应器投用前的内外部检验中，发现了大量的焊缝表面裂纹和内部埋藏裂纹。
Spot-weld the side wind ow aperture to the inside of the side section.
将侧窗接缝点焊到侧面部件内侧。
Accessible seams on the inside of the enclosure shall be welded with continuous filet weld.
在里面无障碍接缝外壳的应连续菲力焊接的焊缝。
If the sheet is relatively thin, the range of welding parameters obtained that can get better weld quality is wider. Heavily plastic flow of the weld metal occurs inside the weld during the process.
板材厚度较小时，形成良好焊缝的规范参数范围较宽，焊接过程中接头内部发生了剧烈的塑性流动。
Occasionally porosity can be found in the face of the weld while sometimes the face may appear porosity free, but deep inside the weld, porosity may exist.
偶尔孔隙中可以找到面对焊缝而有时面对可能出现孔隙免费的，但内心深处的焊缝，孔隙度可能存在。
Fatigue beaked on weld seam more than other places. Fatigue crack initiation occurred inside materials and fatigue fracture was analyzed by SEM.
疲劳试验发现，疲劳试样断裂位置多发生在焊缝处，并对疲劳断口进行了SEM分析。
Slot welding the 2nd side onto the divisions where there is not enough room for access to weld them on the inside.
槽焊接上的第二方面的分歧那里没有足够的空间进入焊缝他们在里面。
Slot welding the 2nd side onto the divisions where there is not enough room for access to weld them on the inside.
槽焊接上的第二方面的分歧那里没有足够的空间进入焊缝他们在里面。
应用推荐