Notes 1 GD2 of input shaft is a value in dwell range.
入力轴的GD2是在停留范围内的数值。
Any rotation of the clutch disc turns the input shaft.
从动盘的旋转带动变速器输入轴随之转动。
5 input shaft heat treatment quality is not qualified.
5输入轴的热处理质量不合格。
Roller bearings on the input shaft with a minimum of 100,000 hours L10 bearing life.
输入轴上的滚柱轴承最低l 10使用寿命为10万小时。
Specification: direction of rotation of output shaft varies with that of input shaft.
说明：当输入轴旋转方向改变，输出轴相应改变。
The power input shaft of the main speed reducer is provided with an optoelectronic pulser;
在主减速器动力输入轴上设装光电脉冲器；
This locks the engine to the transmission input shaft, causing them to spin at the same speed.
这样使发动机和传动系输入油可靠地接合，使它们以相同的转速运转。
The motor can be directly commected to the ball reducer as shown with the hollow input shaft type.
如图所示，电机可直接连接于空心轴形式输入的球减速机上。
The engine crankshaft can then turn without turning the clutchdisc and the transmission input shaft.
之后发动机曲轴转动起来，不需离合器和变速器输人轴的转动。
Input Method: electrical Direct, electrical connection, or a belt input shaft, flange type connection.
输入方式：电机直联、电机皮带联接或输入轴、联接法兰输入。
The gear section also has the input shaft and the output shaft needed to transmit power to the drive wheels.
齿轮段也有输入轴和输出轴，它必须吧动力传递给驱动轮。
The input shaft and output shaft of this kind of double universal couplings are non-parallel, non-intersecting.
这种联轴节的输入轴与输出轴成空间交错轴关系。
The transmission ratio of the input shaft and the output shaft can be changed by regulating the length of the oil cylinder.
调节油缸的长度，改变输入轴和输出轴间的传动比。
However, the greater the displacement of the input shaft axis from the crown wheel axis, the lower the mechanical efficiency.
然而，更大的车轮从冠轴输入轴轴线位移，机械效率降低。
For example, using the gearbox fitted to the shell, the need for gearbox input shaft axis lines at the engine crank axis lines.
例如，将变速器装配到离合器壳上时，必须使变速器输入轴的中心线与发动机曲轴的中心线对准。
The rotating action of the pump against the fluid and the action of the fluid against the turbine turn the transmission input shaft.
泵轮的旋转作用冲击液体，液体的作用推动涡轮旋转变速器输入轴。
Extremely low cost. Standard high-precision ground spindle. Standard flat mounting arrangement. High overhung load capacity input shaft.
价格低廉，精密钻孔轴，平坦安装，悬臂式负载能力输入轴。
Prior to startup, get rid of tape from labyrinth seal end of input shaft, labyrinth seal outer surface of output drive flange and respirator.
启动前应除去减速机输入轴迷宫密封端面和输出传动法兰迷宫密封外圆表面，以及呼吸器上的防锈包装及胶带。
2 the curvature radius and the change curve of the transition fillet at the shoulder of the input shaft of the reducer are not carefully considered.
2减速机输入轴处轴肩处未细致考虑过渡圆角的曲率半径和变化曲线使应力集中严重发生疲劳破坏。
Input seal: input carbon seal was blistered on the sealing face; the input carbon seal was scrap. Sealing face on the input shaft was scratched, and was lapped.
输入轴碳封圈密封面产生浮泡；碳封圈报废。输入轴上的密封面划伤，研磨修复。
The reference is chosen tobe the base of the input shaft and the output shaft of the gearbox, and the top and the two technological holes are used as the reference.
基准选择以变速箱箱体的输入轴和输出轴的支承孔作为粗基准，以顶面与两个工艺孔作为精基准。
With the input shaft key secured with a set screw, an input and output shaft key configuration delivers optimum positive connection for superior torque transmission.
输入轴键受到固定螺钉的保护，输入和输出轴键配置实现最佳的刚性连接以提供更好的扭矩传送。
The input shaft is connected to the ring gear (blue); The output shaft is connected to the planet carrier (Green) which is also connected to a "multi-disk" clutch pack.
输入轴与齿圈（蓝色）连接，输出轴与行星架（绿色）相连，行星架上装有多片离合器。
The utility model relates to a full gear driving device for a micro tilling machine, which comprises a driving box body, a driving input shaft and a driving output shaft.
一种微耕机全齿轮传动装置，包括传动箱体、传动输入轴和传动输出 轴；
Power is delivered to a spline shaft by a power output shaft of a tractor via a universal transmission shaft, an input shaft of a gear box, and a conical gear pair in mesh;
动力由拖拉机的动力输出轴，通过万向传动轴、传动箱的输入轴、经互相啮合的圆锥齿轮付传递至花键轴；
At a shift-down time, the target value of the engine speed is set according to the actual speed determined from the signal of the input shaft speed of the transmission system.
在换低速档时，根据从变速装置的输入轴转速的信号求得的实际车速，来设定发动机转速的目标值。
The side output shaft of the gear box connects with the input shaft of the wheel box through a universal coupling, the stubble cleaner shaft is driven by wheel box output shaft.
变速箱侧输出轴通过万向联轴节与传动箱输入轴相连接，灭茬轴则由传动箱输出轴带动。
Secondly, the forces of inner cam rings, planetary bearings, counter weights and input shaft are solved after the acting force between the cam and the rollers has been calculated.
其次，本文在确定了凸轮-针轮副的啮合力的基础上，对整个机构的内齿板、行星轴承、配重及其输入轴进行了受力分析。
Secondly, the forces of inner cam rings, planetary bearings, counter weights and input shaft are solved after the acting force between the cam and the rollers has been calculated.
其次，本文在确定了凸轮-针轮副的啮合力的基础上，对整个机构的内齿板、行星轴承、配重及其输入轴进行了受力分析。
应用推荐