Slope deformation monitor consists of surface displacement measurement and inner deformation measurement using inclinometers.
边坡监测包含了边坡表面与内部测斜。
To solve the deformation and accuracy problem in the inner hole machining, we utilized stitching and partition process.
再采用粘结分离工艺，简单、巧妙地解决了叶片分离加工中叶片易变形、内孔精度易丧失的问题。
The criterion of rock failure and inner boundary condition need to be considered carefully while processing the fault growth, movement and deformation.
断裂的发生、运动与变形涉及岩石破裂准则与内部边界处理。
The closer to the inner parts of lava flows, the smaller vesicles and the less obvious deformation.
越往熔岩内部气孔越小，变形越不明显。
However, for the metal mechanical parts which are processed by mechanical method, the influence of its inner residual stress on the thermal deformation error should be considered.
然而，对于由机械加工获得的金属机械零件，必须考虑零件内存在的残余应力对热变形误差的影响。
The tide interference is one of the main causes which affects the inner precision of deformation data at Xiamen seismic station.
海潮干扰是影响厦门台形变资料内在精度的主要因素之一。
The inner maximum resistance force and the maximum stress of the specimen decreases as the deformation temperature increasing.
在形变速率相同的条件下，随变形温度的升高，试样内部最大形变抗力及最大应力呈下降趋势。
A fast iris location algorithm is proposed to aim at the problems such as inner edge deformation in iris and blurring outer edge leading to difficult iris location.
针对虹膜内边缘易变形，外边界边缘模糊从而虹膜定位困难等问题，提出了一种快速虹膜定位算法。
An analysis of abnormal deformation, which was found in the inner pipeline cross-section during the maintenance, was made on the Zhong-Kai gas transportation pipeline.
就中开线春亭段输气管线在检修维护中发现的内层管道截面非正常变形问题进行了分析研究。
Stress and strain contours of the stator under an even inner pressure and a pressure difference, deformation distribution varied with pressure were obtained.
对定子和螺杆进行接触计算，结果表明：定子与螺杆在圆弧顶接触时，剪应变和变形最大；
The math-physic model of stressed lap′s deformation and it′s emulated results in the inner 80% region and the whole region caused by the 12 drivers around the lap are given.
给出了应力盘变形的数学物理模型及在周边12个驱动器的作用下应力盘全口径和80 %口径范围内的变形仿真结果；
The results show that the aggregation of contaminant is the inner cause of Copper pipe crack, while the thermal stress formed during welding and winding deformation is another two important factors.
结果表明：夹杂物局部偏聚是铜管断裂的内在原因。焊接时产生的热应力及弯曲变形是铜管断裂的外部诱发因素。
This paper deals with the inner force and deformation of curtain wall glass caused by vertical and side forces by using nonlinear theory of large deflection.
探讨了幕墙玻璃在纵力和侧力的共同作用下的内力和变形根据实际的变形状态运用大挠度的非线性理论。
The research mainly focuses upon the deformation mechanism, relationship among forming parameters, and forming process optimization of inner gear spinning.
本文的研究工作围绕杯形薄壁内齿轮旋压变形机理、工艺参数间的制约关系、成形工艺以及工艺参数的优化展开。
The elastic deformation, the inner mechanism and the rigid motion of systems can be properly considered.
分析中可考虑体系的弹性变形、内部机构和刚体运动。
Compared with structures on the ground, the seismic deformation of underground structures is smaller, while inner force response is larger.
与地上框架结构相比，地下结构的地震变形反应相对较小，但内力反应很大。
For the inner crack appearing often in round-rod rolling steels in the production, the influence to the crack from deformation extent and mechanical condition in the deformation region is discussed.
圆棒轧材在生产过程中经常出现内裂纹，本文研究了变形程度和变形区力学条件对内裂纹的影响。
Then, the effect of model parameters on displacement of soil and inner stress and displacement of bearing pile were discussed and rule of pit deformation was studied too.
讨论模型参数对土体变形及支护桩变形与内力的影响和基坑变形规律的研究；
Based on the 300mw unit, calculations of high pressure inner cylinder on different typical conditions are carried out, and the deformation trends are concluded.
以300MW汽轮机组为对象，对高压内缸进行几种典型工况的分析计算，得出了高压内缸在不同工况下的径向变形趋势并分析了变形原因。
The strength of inner lining has smaller impact on the stress and deformation of the liner, and in the specific engineering C30 concrete is enough.
内衬强度对衬砌受力和变形的影响较小，实际工程中采用C30混凝土即可。
As a successively and locally plastic deformation process, ball spinning is applied in order to manufacture high-strength and high-precision thin-walled tubular part with longitudinal inner ribs.
作为一种连续局部塑性成形工艺，滚珠旋压被应用于制造高强度、高精度的纵向内筋薄壁筒形件。
When plate loading test is carried out, the deformation properties of surface layer will be different from that of inner layer because of the existence of disturbance.
现场岩体变形试验时，试验点部位岩体由于受卸荷、松弛影响，表层岩体变形性能与深部未扰动岩体变形性能存在差异。
The effect of inner corner radius on the plastic deformation behavior in equal channel angular pressing was investigated using finite element method.
运用有限元模拟的方法研究了内角半径在等径角挤压过程中的作用。
The effect of inner corner radius on the plastic deformation behavior in equal channel angular pressing was investigated using finite element method.
运用有限元模拟的方法研究了内角半径在等径角挤压过程中的作用。
应用推荐