The focal points of designing cyclone separator were involved in cylinder length, dimension of inlet and outlet pipe, cone and filling tube.
简体的长度、进气管和排气管的尺寸以及锥体和下料管是设计旋风分离器时要考虑的重点。
Lateral inlet operating pressure, lateral length, terrain slope and lateral diameter are the important parameters that have effects on drip irrigation uniformity.
低压滴灌毛管进口工作压力、铺设长度、地面坡度及毛管管径是影响滴灌灌水均匀度的重要参数。
The effects of intake chamber volume, diameter and length of inlet duct and inlet manifold on volumetric efficiency were analyzed.
分析了进气总管和进气支管的管长、管径以及进气腔容积对充气系数的影响规律。
And the prediction results from this new model show that the slug length is not dependent on its average value and the distribution at the pipe inlet.
模型对液塞长度的预测结果基本不受入口平均值和分布形状的影响。
The experimental study was focused on the effects of inlet air temperature, inlet air flow rate and accelerating pipe length on ISCs volumetric evaporative coefficient.
实验主要研究了空气进口温度、空气进口流量、液滴加速管的长度对ISC容积蒸发系数的影响。
Estimates capacity and power required for compressing a gas mixture from an Inlet pressure to Desired Outlet pressure for a given cylinder diameter, rod diameter, stroke length and RPM.
此压缩机在线计算程序可计算从入口压力压缩到出口指定压力，在给定活塞直径、连杆直径、冲程长度和转速的情况下，压缩气体混合物所需的压缩机容量和功率。
This paper discussed the selection of the size(length, width and height) of the oven, the inlet mode of the hot air and the design of outlet to increase the utilization efficiency.
讨论了洞道式干燥器的长度、宽度、高度的选择，热空气进入方式和排气口的设置，以提高其热空气的利用率。
The longer the expand length is, the smaller the inlet diameter is, the greater the pressure loss of expand muffler element is.
扩张腔腔体长度越大、进出口管管径越小，扩张腔消声器的压力损失越大。
The essential performance had been achieved by testing through changing boundary layer ejector pumping capacity, mixing chamber clapboard length, the counterpressure, main inlet mass flux and so on.
以常温空气为介质，通过改变扩压器附面层抽吸能力、混合室隔板长度、扩压器出口反压及主进气流量等条件进行试验。
This paper introduced the fast detection device of acting length of the sealing face which is suitable for on line detection of inlet and exhaust valve of the engine.
本文介绍了密封面作用长度的快速检测装置，此装置适用于发动机中进排气门的在线检测。
The turbulence induced by the defects of nozzle, such as the burr at the inlet and outlet, and the roughness of the wall, is the main cause to decrease the length of intact jet.
当射流速度比较大时，喷管的缺陷如进口出口的毛刺和流道壁的粗糙度是诱发湍流使射流破断的主要原因。
The turbulence induced by the defects of nozzle, such as the burr at the inlet and outlet, and the roughness of the wall, is the main cause to decrease the length of intact jet.
当射流速度比较大时，喷管的缺陷如进口出口的毛刺和流道壁的粗糙度是诱发湍流使射流破断的主要原因。
应用推荐