The injection phase-locked method introduced in this paper can be used to overcome this disadvantage.
介绍了用注入锁相的方法来弥补这个缺陷。
An attacker may use directory traversal and cross-site ccripting during a scan phase and then hit it with an SQL injection or an RFI in the exploit phase.
在扫描阶段，攻击者可能会利用路径遍历和跨站点脚本；在攻击阶段，黑客可能会利用SQL注入或远程文件包含进行攻击。
A heterodyne interference is caused by a frequency modulation of a laser diode (LD) with a ramp injection current, and a linear phase detection is realized.
传感器利用注入结电流直接调频的半导体激光(LD)产生外差干涉，从而实现了干涉相位的线性检测。
The phase behavior experiment shows that the hydrocarbon gas injection makes the results of visbreaking and swell of reservoir fluid obvious in Gao 13 Block.
注气相行为特征实验表明，注烃气对高13断块油藏流体的降黏、膨胀效果显著。
Objective to establish a reversed phase high performance liquid chromatography gradient elution method for determination of the related substances in allopurinol sodium for injection.
目的建立测定注射用别嘌醇钠有关物质的高效液相梯度洗脱法。
Conclusions the reversed phase high performance liquid chromatography gradient elution method is simple and accurate for the determination of the related substances in allopurinol sodium injection.
结论高效液相梯度洗脱法可用于测定注射用别嘌醇钠中的有关物质。
Study on interfacial tension, composition, density, viscosity and saturation of gas pha - se and liquid phase front in the slim tube under various injection pressures and injection rate.
分别研究了不同注入压力和注入气量下，细管中注气混相驱前缘和过渡带中气液两相的界面张力、组成、密度、粘度及饱和度的变化情况。
Based on a thermodynamic model of gas_liquid equilibrium, the variation of phase behavior in a volatile oil system during gas injection has been investigated.
根据气液两相相平衡热力学模型研究了某挥发油油藏在注天然气过程中油藏体系相态特征的变化规律。
The circs of collision of particle(granule and molecule)in the powder and binding two-phase flow for powder injection molding is studied.
分析了粉末注射成形中粉末—粘结剂两相流动中粒子（颗粒与分子）碰撞的情况。
The forming methods of microcellular plastics include batch microcellular foaming, continuous extrusion, injection molding and phase separation.
微孔塑料的成型方法主要包括间歇成型法、连续挤出成型法、注射成型法和相分离法等，并且各有优缺点。
The principles of using signal injection method to detect single-phase earth fault of distribution network at present are compared and analyzed.
对目前配网采用信号注入法检测单相接地故障的原理进行比较分析。
The signal injection method is widely used for automatic selecting fault line in indirectly earthed power system, which has great effect in the system of single-phase ground fault.
注入信号法是一种效果较好的选线方法，其原理广泛应用于小电流接地系统单相接地故障的自动选线。
The design is characterized by short flow, double pot injection, concentrated phase transmission of charge and discharge, advanced and rational control technology.
该设计具有流程短并罐喷吹，上出料浓相输送，控制技术先进合理等特点。
It will provide significant guide for oilfields, especially for those having high gas-oil ratio in western China developed by abundant associated gas or gas-injection miscible phase process.
这将为西部油田特别是高气油比油田利用丰富的伴生气、采用注气混相驱开发有一定的借鉴意义。
An unstable process is transformed into a minimum-phase system through mirror-injection, then solve the robust controller using closed loop gain shaping algorithm.
通过镜像映射将非稳定过程转换成最小相位系统，然后用闭环增益成形算法求解鲁棒控制器。
In this paper, a method of chaotic controlling is presented via controlling the phase in semiconductor lasers under to external optical injection.
提出外部光注入半导体激光器混沌相位控制方法，通过周期调制注入光的相位相移将激光器的混沌控制到多种周期状态。
So it is important to research the nonequilibrium phase behavior during the process of gas injection.
因此研究注气过程中的相态变化非平衡性具有重要意义。
The liquid-phase sample injection valve ensured the sampling reproducibility.
使用液相进样阀液态直接进样保证了试样的代表性。
Based on clustering FSVM and current injection method, a new method using two steps for single-phase grounding fault location of distribution feeders in networks with ungrounded neutral is proposed.
提出小电流接地系统实现单相接地故障定位的新方法。该方法应用基于聚类的FSVM和电流注入法分两步实现故障定位。
The nano crystal is purified and then dispersed in the external aqueous phase to form the contrast agent for intravenous injection.
纳米晶经纯化后分散于外水相中，得到可静脉注射的造影剂。
The filling phase of the injection moulding process greatly affects the quality of the end product.
在注塑过程中填充阶段对产品最后的成型的质量有着巨大的影响。
Three-dimensional, three-phase, black-oil mathematical models are established for the gas injection process in reservoirs.
建立了考虑分子扩散作用的油藏气驱三维三相黑油数学模型。
This research hews out a new way for phase research, the results is reference valuable for optimizing gas injection scheme.
此次研究为目前相态研究开辟了一条新的道路，所取得的成果为优化注气方案有一定的参考价值。
This paper proposes an injection current based three phase power flow method.
介绍了凸极无刷直流电动机转子位置检测的电流注入法。
The development process of injection lance castable for molten iron pretreatment at Baosteel 3rd Phase Project and its application were introduced.
介绍了宝钢三期工程铁水预处理喷枪浇注料的研制过程及使用情况。
The development process of injection lance castable for molten iron pretreatment at Baosteel 3rd Phase Project and its application were introduced.
介绍了宝钢三期工程铁水预处理喷枪浇注料的研制过程及使用情况。
应用推荐