Filtering, cooling of oil after injection of new head.
过滤、冷却后的油重新注入机头。
It is usually said mold, such as TV sets, telephone shell, plastic barrels and other commodities, the plastic injection molding mold cooling heating software produced.
也就是通常人们说的模子，比如电视机、电话机的外壳、塑料桶等商品，是把塑料加热软件注进模具冷却成型生产出来的。
Aftershocks on Monday briefly cut power to backup pumps, halting the injection of cooling water for about 50 minutes before power was restored.
星期一的余震主要切断了后备水泵的电源，中断了冷却水的注入。到恢复供电已经过去了大约50分钟。
The cooling system of injection mold has significant effect on the quality of the plastic parts.
注塑模具的冷却系统对塑料件的质量有至关重要的影响。
Several methods to determine the cooling time of injection molded slabs of crystalline plastics are discussed based on the theory of heat transfer.
从传热学基本原理出发，推导出结晶性平板状注塑制品冷却时间的几种计算方法。
The injection tooling with the designed optimal conformal cooling channels was fabricated by using the selected laser sintering technique.
利用选择性激光烧结快速制模工艺制造出设计好的具有最优随形冷却水道的注塑模具。
Based on the variation of temperature in injection molded parts, the simulation of cooling takes consideration of the cooling stage of the part after ejection.
以注塑制品的温度变化为对象，考虑了注塑制品出模后的冷却过程。
In this paper, a PC-program developed for the prediction of the parameters of cooling in injection molding is reported.
本文所介绍的PC级软件，能预测注射成型冷却过程的主要参数。
The design manner of cooling system of CD injection mold was mainly introduced, and the cooling water channel of moving plate, stationary plate, sprue and punch etc were detailed.
介绍了光盘注射模冷却系统的设计方法，以及动镜面、定镜面、浇口与凸模的冷却水路等。
The temperature on mold cavity's surface affects the melt's flow and cooling in the course of injection molding, then has an important part in the solution of injection molding.
在注塑加工数值模拟过程中，模腔的表面温度直接影响塑料熔体的流动和固化过程，所以模腔表面温度的计算对注塑数值模拟的结果起着极为重要的作用。
This paper discusses the three factors that affect the deformation of injection molded parts:simple nonuniform shrinkage, part cooling and molecular orientation.
本文分析了注塑成型过程中简单收缩、冷却、 分子取向等因素对注塑件变形的影响。
In addition to the charging function, the centrifugal pumps also serve as the high head safety injection pumps during emergency core cooling system operation.
除了上充功能，应急堆芯冷却系统运行时，离心上充泵用作高压安注的一部分。
A variotherm injection molding technique with steam heating and coolant cooling was studied and its molding process was also designed.
研究了一种利用蒸汽加热和冷却水冷却的变模温注塑工艺，制定了其工艺流程。
The injection mold cooling system design is very important to improve the mold design and manufacture of standard and quality of products.
注塑模具冷却系统对于提高模具的设计制造水平和制品的质量是非常重要的。
Injection realize, in the pressure cooling, the use of low temperature water to mold a cooling cuisine, so as to narrow the products of the cooling time, drive up produce efficiency.
注射实现，在保压冷却时，用低温水对模具举行降温料理，以便缩小制品的冷却光阴，抬高出产效率。
As the application of 3d temperature field numerical simulation, the thermoplastic's cooling procedure of injection molding has been analyzed.
作为三维温度场模拟的应用，分析了热塑性塑料注塑成型模具冷却过程的温度场。
After a brief introduction to the structure of injection moulds, the research situation of CAE-based optimization plan for the feed system and cooling system of injection moulds was discussed.
在简单介绍注射模结构的基础上，对基于CAE的注射模浇注系统和冷却系统优化研究概况进行了论述。
Based on the 175F type swirlprechamber air cooling diesel engine, through redesigning cylinder head and piston etc. , new 175F type direct injection air cooling diesel engine is formed.
在175F涡流预燃室风冷柴油机的基础上更换气缸盖、活塞等零件，改成新的175F直喷式燃烧室风冷柴油机。
The basic principle of cooling simulation technology and its application in the injection mold cooling system and the design of the processing parameters are introduced.
介绍注射模冷却模拟技术的基本原理及在注射模冷却系统和工艺参数设计中的应用。
The cooling system greatly influences both the quality of plastic production and efficiency of the injection molding.
注射模冷却系统的设计不但关系到塑件质量而且也关系到注射成型生产效率。
It is necessary to determine switchover time to simultaneous cold and hot leg safety injection during LOCA long-term core cooling.
在失水事故长期冷却过程中，必须确定安全注射系统从冷段注射切换到冷热段同时注射的切换时间。
The design of cooling system for plastic injection mould has much to do with the production efficiency and product quality.
注塑模冷却系统的设计直接影响着注塑生产效率及塑件质量。
Finally, a reasonable injection mold casting system, cooling system, the cooling effect is good, the overall structure of the mold and reasonable.
最后的注塑模具浇注系统合理，冷却系统的冷却效果良好，模具整体结构合理。
Liquid silicon rubber injection moulding has constant cooling pressure to the cable. It is Low in electricity output while "breathing" together the cable.
液体硅橡胶注射成型对电缆本体有恒定的收缩的收缩压力，与电缆同“呼吸”局部放电最低。
The optimization of cooling system for injection dies is also studied in the article.
对于塑模冷却系统的优化问题，亦作了探讨。
To most injection mold, the cooling is realized through the coolant flowing in pipe network.
对大多数模具，冷却是通过冷却液在冷却管网内的流动来实现的。
Faster injection (up to a point): less cooling during filling, hence a thinner initial frozen layer, lower viscosity due to shear thinning;
较快注塑（到点）：在填料过程中冷却较少，因此初始固化层较薄，由于剪应变稀少而粘性较低；
Taking the forming of computer case panel as an example, the process of the filling, cooling and warpage of the plastics parts in the injection molding were simulated by means of MPI software.
以电脑机箱面板为实例，使用MPI软件对塑料件注射过程中的填充、冷却、翘曲情况进行模拟。
A software for cooling analysis in injection molding is introduced.
介绍了一个注塑模冷却分析软件系统。
A software for cooling analysis in injection molding is introduced.
介绍了一个注塑模冷却分析软件系统。
应用推荐