In nozzle theory, flow is assumed to be one-dimensional.
在喷嘴的理论，流量是假设为一维。
The method used to calculate the temperature drop in nozzle is proposed.
给出了气嘴节流温度计算方法，并分析了节流后温降的原因。
The calculating method of equilibrium flow in nozzle is described ein detail.
尤其是喷管平衡流的计算方法文中作了详细的阐述。
Several other problems in nozzle design under friction-existing condition are also discussed.
还探讨了摩阻存在条件下喷管投计中的其它几个问题。
Based on three-dimension finite element model, transient temperature field in nozzle was calculated.
基于三维有限元模型，计算了喷管的瞬时温度场。
A generalized finite element method (GFEM) is presented for the calculation of incompressible flow in nozzle.
本文将广义有限元法用于求解不可压缩管流。
Therefore, the removal way of cemented carbides in nozzle-type ELID grinding was mainly ductile removal mode.
因此，硬质合金材料去除机理主要为延性去除磨削方式。
The local ablation of thermal insulation barrier in nozzle convergence region and of throat insert is analysed.
分析了喷管收敛段绝热层及喉衬的局部烧蚀问题；
Such separation helps to inhibit premature reaction which could result in nozzle blockage or poor printer firing.
这种分离有助于抑制过早反应，这可能导致喷嘴堵塞或贫穷打印机射击。
There are particles on whole cross section of nozzle divergent section and this fact shows that there is no"no particles zone"in nozzle divergent section.
喷管扩张段整个截面上都有粒子分布，说明喷管扩张段中不存在“无粒子区”；
It has no insoluble matter separated out in storing for long term and no jamming in nozzle, and it may be used to print clear and homogeneous text and graph and without fading in water.
该墨水长期存放后，没有不溶物出现，不堵塞喷嘴，经三年试用，打印的文字、图像均匀、清晰，且遇水不褪色。
Theoretically, it is proved that for both these engines, the properties of two-phase flow in nozzle can be analysed with a common combined parameter which is equivalent to exhaust velocity.
从理论上证明：对这两类发动机的两相喷管流动特性可以通过一个共同的组合参数——当量排气速度来进行分析；
In addition, too much cutting speed and big nozzle height can cause and the increase of the poor incision width.
另外，过大的切割速度和过大的喷嘴高度都会引起切口上下宽度差的增加。
In the steam condensate oil to the nozzle or sharp curve place, oil steam issue is very outstanding.
在油蒸气容易凝结的喷嘴或急弯处，油蒸气问题十分突出。
In addition, it was found that performance of inner nozzle is the largest part of that of linear plug nozzles, accounting for more than two thirds of whole engine's performance.
另外在计算过程中发现，内喷管的性能是整个线性塞式喷管性能的主要组成部分，占了整个塞式喷管性能的三分之二以上。
Slowly pour in new engine oil using a clean container or a fuel nozzle.
使用干净的容器或加油嘴缓缓倒入新的发动机机油。
There is an opening in the bottom of the ladle called nozzle which is sealed with a vertical refractory stopper.
盛钢桶底有个叫作水口的孔，由一根直立的耐火材料做的塞棒堵住。
This paper presents a method in which using computer image identity tests the leakage of fuel spray nozzle in diesel engine.
提出了采用计算机图像识别技术的柴油机喷油嘴渗漏检测方法。
Similar in concept to HP's Page-wide array printhead technology, this design allows a much wider print swath in a single pass with guaranteed perfect nozzle alignment, he says.
他说，在概念上类似于惠普的打印喷头技术，这种设计能够保证大范围的打印片能够很好的对准打印喷嘴。
The deflecting nozzle thrust vector control is usually used in a large solid booster.
对大型运载火箭的固体助推器，通常采用摆动喷管推力向量控制。
In the numerical simulation of flows in a nozzle, how to capture shock wave draws much attention.
在喷管流动问题的数值模拟中，激波的捕获一直是一个研究的重要方面。
The apparatus has been used in investigating the spray formation of a pintle nozzle.
文中利用该装置研究了轴针式喷嘴的喷油过程，探讨了喷嘴油束形成的特征。
The basic structure and working principle of the piezoelectric nozzle is introduced, the design concepts aiming at the nozzle in designing screen manufacturing machine are discussed.
本文介绍了压电式喷头的基本结构和工作原理，讨论了在设计制网机时针对压电式喷头所采用的一些设计方法。
The improvement of immersion nozzle in square billet caster is introduced, the result extinguished.
介绍了邯钢方坯连铸机浸入式水口的改进，保护浇注效果显著。
The merit, usage of microcellular foam plastics and the importance of nucleation nozzle in the processing is generalized.
概括了微孔塑料的优点、用途及成核喷嘴对加工过程的重要作用；
This paper has simulated two-phase flow in a small expansion ratio nozzle.
本文对小扩张比喷管内的两相流场进行了数值模拟。
The type, rating and facing of nozzle flanges shall conform to those specified in Purchaser's drawing or data sheet.
设备口法兰的类型、等级及端面应符合买方图纸或数据表的规定。
The type, rating and facing of nozzle flanges shall conform to those specified in Purchaser's drawing or data sheet.
设备口法兰的类型、等级及端面应符合买方图纸或数据表的规定。
应用推荐