The hot deformation is one of the machine tool guideways deformations.
机床导轨热变形是导轨变形的一种形式。
The effect of hot deformation amount on impact toughness for Vanadium white cast iron was studied.
研究了热变形量对钒白口铸铁冲击韧性的影响。
This paper deals with the granular carbides formation from hot deformation in high chromium cast steel.
本文探讨了热变形高铬铸钢中颗粒状碳化物的形成。
Direct quenching, n-in thermomechanical processing, quenching immediately following the final hot deformation.
直接淬火,名词,在形变热处理过程中,最终热变形之后立即进行淬火。
The hot deformation behavior of a self-developed zinc based alloy was investigated by isothermal compression test.
采用等温热压缩试验对一种自行研制的高强度易切削锌基合金进行热变形行为的研究。
The results show initial microstructure characteristics have significant influences on the hot deformation of alloys.
结果表明:组织特征对合金的热变形行为有显著影响。
It is suggested that both heat treatment and hot deformation should be adopted to improve the M2 cast strip microstructure.
建议在工业铸带的后续处理中同时采用高温热处理和热变形工艺以改善铸带组织。
The influence of cooling rate after 40 % hot deformation on structure and properties of high carbon chromium cast steel was studied.
研究了经40%热变形后不同冷却速度下高碳铬铸钢的组织和性能。
The microstructure evolution of Q235 plain carbon steel in multi-pass hot deformation was investigated by means of hot compression simulation.
利用热模拟压缩变形实验研究了Q 235碳素钢多道次热变形及后续处理过程的组织演变规律。
Some new secondary phases precipitates after hot deformation. The mechanical properties of the alloy after deformation treatment are improved.
合金在变形处理后有新的第二相析出,且合金的力学性能有很大提高。
The microstructure features at different hot deformation conditions were analyzed with optical microscope (OM) and transmission electron microscope (TEM).
利用光学显微镜(OM)和透射电子显微镜(TEM)观察合金不同热变形条件下的组织形貌特征。
The hot deformation behavior of industrial continuous-casted duplex stainless steel 2205 under different temperature and different strain rate was investigated.
研究了工业连铸双相不锈钢2205在不同温度和应变速率下的热变形过程。
Error analysis shows that the constructed constitutive relationship has good accuracy and can preferably describe hot deformation behavior of TB6 titanium alloy.
误差分析表明,所建的本构关系具有较好的精度,能较好地反映TB 6钛合金的热变形行为特征。
LI H J. Study on hot deformation behavior of China low activation martensitic steel for fusion reactor[D]. Beijing:University of Science and Technology Beijing, 2011.
[14] 李华杰。聚变堆用中国低活化马氏体钢热变形行为研究[D]。北京:北京科技大学,2011。
The coincidence of the predicted grain sizes with measured ones show that the method is able to successfully predict the microstructure of metals after hot deformation.
预报值与实测值吻合良好,表明本文方法已能成功预报热变形后的金属微观组织。
Pretreatment condition, i. e. cold or hot deformation, has important effects on microstructure evolution, and deformation of samples is a necessary step in SIMA process.
冷、热变形预处理条件对组织演变产生一定的影响,给试样施加变形是SIMA工艺的必要步骤。
This paper researches the influence of technology parameters of hot deformation on the nonhomogeneous deformation between the austenitic grains and different zones within the grains.
本文研究了热形变工艺参数对奥氏体晶界和晶内不同区域的形变程度不均匀性的影响。
The relations of the thermomechanical parameters with strain were obtained using the hyperbolic-sine mathematics model and the hot deformation constitutive relationship was established.
采用双曲正弦模型确定了该材料的热变形参数随应变量的变化规律,建立了相应的热变形本构方程。
By integrating the thermomechanical coupled FEM with mathematical model of microstructure evolution, the paper proposes a numerical prediction method for microstructure during hot deformation.
将热力耦合有限元方法与金属微观组织演变数学模型相结合,提出了热变形过程微观组织的数值预报方法。
By integrating the thermomechanical coupled FEM with mathematical model of microstructure evolution, the paper proposes a numerical prediction method for microstructure during hot deformation.
将热力耦合有限元方法与金属微观组织演变数学模型相结合,提出了热变形过程微观组织的数值预报方法。
应用推荐