Hot curing in 70 C dry-air is the optimal industrial curing mode and the best curing mode is hot wet-dry cycle curing of hardened hemihydrate gypsum-fly ash paste.
干热养护是半水石膏粉煤灰胶结材硬化体的最佳工业养护方式；半水石膏粉煤灰胶结材硬化体最适合干湿循环热养护。
The flow diaorams of a hot water unit for tire curing is introduced anb discussed.
文中介绍并讨论了轮胎硫化用热水站的工艺流程。
Alcohol curing equipment, hot air curing device, Easy cutter etc.
酒精固化装置、热吹风固化装置、简易切刀等。
Unlike dip coatings, electrodeposited paint is not washed off in enclosed areas by hot vapors during curing.
与浸法涂装不同，电泳沉积在内腔部位的涂膜，在烘干过程中不会被热蒸汽洗掉。
It is fine white nontoxic and no curing pollution with specific gravity of 1.08. It can slightly dissolve in hot ethanol, but not in water.
白色细微粉末，无毒，无硫化污染，比重1.08，不溶于水，微溶于热的乙醇。
The factors which influenced adhesive strength, curing speed of reactive polyurethane hot melt adhesive were studied.
考察了各因素对反应型聚氨酯热熔胶粘接强度、固化速度等性能的影响。
Emphasis will be primarily on reactive, moisture curing polyurethanes that are applied as one-component liquids, hot melts and binders for wood composition board.
重点讨论单组分液体型、热熔型和木材复合板粘接用反应型、湿气固化聚氨酯胶粘剂。
The performance of the cable repaired is in accordance with the Coal Industry Standard and it has the same effect with curing hot-patch.
修补后的电缆性能符合煤炭行业标准，与硫化热补具有同等效能；
The natural curing time of CPB after hot pressing on the physical and mechanical properties of fast-curing CPB were determined by the hydration of cement.
水泥刨花板卸出压机后的自然养护时间对快速固化水泥刨花板物理力学性能的影响主要取决于板在养护期间水泥的水化情况。
The direct steam curing after the unloading of hot pressing CPB could greatly accelerate thc hydration of cement.
板坯卸出压机后的直接蒸养可大大加速水泥的水化过程。
The review shows the technical points of(epoxy) hot-melt prepreg on the(reasonable) combination of resin matrix, matching of curing agents and(accel…
表明环氧树脂热熔预浸料研制的技术关键是选择合理的树脂体系组合，有较长潜伏期的固化剂和促进剂的匹配及合适的催化剂。
PF resin adhesive by mid-temperature curing is made on the main condition that the "cold-in and cold-out" technique used for bamboo curtain plywood should be changed into a "hot-in and hot-out" one.
将竹帘胶合板的“冷进冷出”工艺改造成“热进热出”工艺，关键技术是降低热压温度，而一种中温固化型的酚醛树脂是实现该技术的主要条件。
PF resin adhesive by mid-temperature curing is made on the main condition that the "cold-in and cold-out" technique used for bamboo curtain plywood should be changed into a "hot-in and hot-out" one.
将竹帘胶合板的“冷进冷出”工艺改造成“热进热出”工艺，关键技术是降低热压温度，而一种中温固化型的酚醛树脂是实现该技术的主要条件。
应用推荐