The experimental result draws hole degree and permeability in the normal atmospheric temperature atmosphere is deferent because of the different rock specimen.
实验结果得出由于选用不同性质的岩样，测试出岩样在常温常压下孔隙度存在差异。
Using scanning electronic microscope, gas hole of flowerpots were studied and analyzed quantitatively and a technical terms, gas hole degree was put forword, on which clustering analysis was based.
利用扫描电子显微镜观察，对花卉盆钵气孔进行分析，量化，并提出气孔度的新概念，按花卉盆钵气孔度大小聚类分类。
The effects of spinneret hole shape, characteristic dimension of spinneret, hole arrangement and cool conditions on degree of profile were discussed.
讨论了喷丝孔孔型、喷丝板特征尺寸、异形孔的排列方式、冷却条件对纤维异形度的影响。
The difference of sedimentation speed, shrinkage degree and direction is the main factor of lawn hollow and hole.
因土壤土质因素出现的土壤沉降速率、收缩程度和方向的不同是导致草坪凹陷、坑洼的主要原因。
Test results show that a certain sensitivity, accuracy and repeatability can be reached in detecting the homogeneous degree of hole diameter of nickel mech by using this principle.
实验结果表明，利用上述原理检测镍网孔径均匀度有一定的灵敏度、精度和重复性。
The diameter, flow, shear rate, draw ratio, pressure difference and degree of profile in different configuration of capillary hole were calculated.
计算不同叶长，叶宽，孔数的喷丝板毛细孔的当量直径，单孔流量，剪切速率，喷头拉伸比，三叶异形孔压力降和异形度。
The random factors were the canopy, slope degree, vegetation type, tree height, shrub height, tree stump height, tree hole density and human disturbance.
而郁闭度、坡度、植被类型、乔木高度、灌木高度、树桩高度、树洞密度、人为干扰的影响不明显。
The effects of dry degree of bottom-hole steam on producing result and effect of drainage velocity in production wells on production result are studied.
还研究了井底蒸汽干度对开发效果的影响和生产井排液速度对开发效果的影响。
The hole size depends on the fluidity of slag phase in pellet and its filling condition to the hole in pellet. The amount and shape of iron phase depend on the reduction degree of pellet.
球团孔隙的大小取决于脉石所形成的渣相的流动性和渣对孔隙的充填状态：铁相的数量及形态则取决于球团的还原程度。
It is the positive feedback trading and self-reinforcing mechanism, which enforced the expectations normalized speed and degree. So the liquidity black hole appears.
正是这种正反馈的交易机制，自我增强了预期归一化的速度与程度，导致流动性黑洞的出现。
Rudder sensitivity, or total movement from one extreme to the other, is controlled by the holes on the rudder horn and, to a degree, by the "pickup" hole on the elevator horn.
鲁德尔敏感性，或从一个极端总运动，另一方面是受舵角上的漏洞，并在一定程度上，由“皮卡”洞角上了电梯。
It's very difficult to make a hole on the wafer with a 45-degree Angle exactly.
在玻璃片上制作精确尺寸的45通孔，并非易事。
To ensure the degree of processing die's hole circle, it is also designed into a stable, high accurate self-centering mold base, thereby improving the dies quality.
确保加工模具孔形的真圆度，该机又设计了稳定、高精度自定心的模座，从而提高模具的品质。
The deflection Angle of the long shaft of the oval relative to the aspiration hole is preferably 10 degree at both sides.
该椭圆的长轴在吸气孔附近，相对于吸气孔的偏转角度较佳为两侧各10度范围内。
The deflection Angle of the long shaft of the oval relative to the aspiration hole is preferably 10 degree at both sides.
该椭圆的长轴在吸气孔附近，相对于吸气孔的偏转角度较佳为两侧各10度范围内。
应用推荐