The nozzle geometric parameters included hole number and diameter, hole angle and hole length-diameter ratio(L/D).
喷嘴结构参数包括喷孔数、喷孔直径、喷孔夹角和喷孔长径比。
The reclining angles can be adjusted by changing the connection of armrest hoo-ks with the 4-hole Angle adjust Panel.
躺卧角度可通过扶手下面的四孔角度调整板调整。
Hole Angle should not exceed 15 degrees any where in the hole unless down hole geological conditions induce such deviation, such as acute fault intersections.
井斜角在井眼任何地方不应超过15度，除非井下地质条件引发了此种偏离，如严重的断层交叉。
And the variation law of the hole collapse pressure of extended reach well along with hole Angle and azimuth mostly decided by the status of the stratigraphic in-situ stress.
大位移井井壁坍塌压力随井斜角与井斜方位角的变化规律主要由地层的原地应力状态决定。
By use of oriented perforator, a certain variance of Angle and azimuth between actual perforated hole and former design is made which mainly caused by hole trace, perforated hole Angle.
采用定向射孔，使得实际射孔孔眼与原来设计的具有一定角度和方位的偏差，主要有孔眼轨道产生的偏差、孔眼角度产生的偏差等。
When he had turned the Angle of the gallery, the distant glimmer of an air-hole disappeared, the curtain of obscurity fell upon him once more, and he became blind again.
当他转过了巷角以后，远处通气洞的光线就消失了，黑幕又在他前面落下，使他再次失明。
Machining the spark plug hole and counter bore at a compound Angle.
加工火花塞孔与反孔的复合角度。
It is especially suitable for drilling of hole with great slope Angle.
这是特别适合钻探孔与伟大的边坡角。
This article introduces mainly calculation of a slanting Angle of crankshaft clamping with the analysis method in machining crankshaft oblique oil hole.
主要介绍在加工发动机曲轴斜油孔时，用解析法计算曲轴装夹时所倾斜的角度。
But various cutting inner hole and small Angle cutting.
可切割各种内孔及小角度切割。
Also, the paper analyses the error caused by capillary action of liquid, error precision, zenith Angle of hole and container diameter.
并对液体的毛细作用、误差精度、钻孔顶角、容器直径引起的误差进行分析。
Well intervals where lift pumps can be located in highly deviated Wells include vertical interval, deflecting interval, Angle maintaining interval and branch rat hole.
大斜度井可供选择的下泵位置有在垂直段安装，在造斜段安装、在稳斜段安装、在分支鼠洞井眼安装。
The reasonable combination of nozzle hole number, impingement angle and valve opening pressure is very important to the new conical spray.
喷孔数、碰撞角度和启喷压力三者的合理配合对第三代伞状喷雾至关重要。
It's very difficult to make a hole on the wafer with a 45-degree Angle exactly.
在玻璃片上制作精确尺寸的45通孔，并非易事。
It is found in the experiments that film hole Reynolds number and Rib Angle have great influence on film hole discharge coefficients.
实验中发现气膜孔雷诺数和肋角对流量系数有较大的影响。
The discharge coefficients of the side-wall outflow hole are affected by the jet angle and cross-flow mass flow rate.
不同射流角度和横流流量对侧壁出流孔流量系数影响很大。
A circular hole equals to the cylinder of the jointing component and gaps through which the nylon can fall down are reserved in the vicinity of the opposite Angle at the bottom of the flat triangle.
在平面三角底边对角的近处，预留下与连体构件的圆柱体相当的圆洞和尼龙丝可以落下的缝隙。
Generally the punching machine can become Angle, processing the wear silk hole should do a special tooling.
一般打孔机都不能变角度，加工此穿丝孔需做一个专用工装。
Angle flange Standard. Flat flange: Specify hole pat-tern. If no drawing provided, flange will be blank.
角法兰标准。平板法兰：指定孔模。如果没有提供的图纸，法兰将为空白。
It can increase the hole inclination Angle range and drill elevation Angle holes, while setting the top drive power head and hole top plate toward the opposite direction.
动力头及孔口板调转方向，可直接钻凿仰孔，大大增加钻孔倾角范围。
"Things aren't always what they seem," the older Angle replied. "when we stayed in the basement of the mansion, I noticed there was gold stored in that hole in the wall."
“事情并不总像看上去的那样，”年长的天使回答道：“当我们在大厦的地下室过夜时，我发现有金子藏在墙洞里。”
Inclinometer is an Instrument testing drift Angle and azimuth of drift hole.
斜仪是一种测定钻孔倾角和方位角的仪器。
The results show that the test error of sample A with large angle coefficient of hole bottom is under 5%, and will become smaller with the increase of furnace temperature;
结果表明，孔底角度系数较大的试样A的检测误差<5%，并且随着炉膛温度的提高，其检测精度也随之提高；
The factors of distance, hole diameter, K value and temperature affecting the measuring precision of K value of Angle probe were analyzed.
分析距离、孔径、K值和温度等影响斜探头K值测量精度的因素。
At present, hole trajectory azimuth Angle is measured mainly with magnetism sensor, but which is restricted by magnetic field and the metal tube around the surveying equipment.
目前的井眼轨迹方位角测量技术主要靠磁通门传感器，这种技术受地磁场及测量体周围金属管体的制约。
For the extended well, high angle drilling, horizontal drilling and deep well drilling, or in the well section of large dogleg severity, or the long open hole, casing wear often happens.
在大位移井、大斜度井、水平井和深井钻井中，或者在狗腿严重度较大的井段，或者在技术套管下入后的长裸眼钻井过程中，常常出现套管磨损问题。
The technology is the same with vertical well, also with high Angle deviated hole, and has broad application range.
该项工艺不仅适用于直井，也适用于大斜度井，因而，适用范围大，应用前景广。
The technology is the same with vertical well, also with high Angle deviated hole, and has broad application range.
该项工艺不仅适用于直井，也适用于大斜度井，因而，适用范围大，应用前景广。
应用推荐