This paper presents the loop control system for high speed wire rod mill at Tangshan Iron and Steel co.
本文介绍唐钢高速线材轧机的活套控制系统。
The application of the online vibration monitoring system in the high speed wire rod finish block was presented.
本文介绍了在线振动监测系统在高速线材精轧机上的应用。
A new method to calculate temperature rise in high speed wire rolling is proposed according to heat line theory.
基于热线理论提出计算高速线材轧制温升的新方法。
The steel's chemical composition and the process parameters influence the mechanical properties of high speed wire.
钢材的化学成分和轧制时的工艺参数影响着高速线材的力学性能。
The characteristics of technology and equipment for high speed wire rod rolling mill in tangshan iron and steel Co.
介绍了唐钢高速线材厂的工艺、设备特点及对引进设备改造工程。
The technological revamping project for speeding - up of home made high speed wire rod mill and the benefits are introduced.
介绍了国产高线生产线提速的工艺改进方案，以及提速工艺实施后产生的效益。
The article introduces the development and application condition of high speed wire and rod product sale information system.
介绍了安钢高线产品销售信息系统的开发与应用情况。
This paper investigates the high speed wire electrical-discharge machining (HSWEDM) of Si3N4-based ceramics by assisting electrode method.
通过辅助电极利用高速走丝电火花线切割加工的方法对绝缘陶瓷氮化硅作了加工实验研究。
This paper introduced the speed-falling problem and its producing factors of the high speed wire rod prefinishing mill in Anyang steel group.
简要介绍了安钢高线机组预精轧机在生产过程中出现的掉转问题，对其成因进行分析，并就治理策略进行了重点研究。
As the rolling speed of the high speed wire rolling mills is very high, the accidental fault is very easy to come out on the transmission parts.
高速线材轧机由于转速较高，其机械传动系统易出现突发故障。
The technology design and its characteristics of a single stand high speed wire rolling mill building in Xiangtan Iron & Steel Co. were introduced.
简要介绍了湘钢华光线材有限公司建设的一套单线高速线材轧机的工艺设计及其特点。
It's very important that accurate position of the edge of start stop shear to high speed wire mill production. Shear would run by accurate controlled.
剪刃位置控制是高速线材生产中所使用的启停式飞剪的关键控制环节，其控制精度的高低直接影响到飞剪的正常工作。
The high speed wire production process is simulated and the simulation system is designed with higher accuracy applicable to various rolling techniques.
采用计算机对高速线材生产过程进行模拟，开发出具有较高准确度同时具有对不同轧制工艺有较好通用性的高线生产仿真系统。
For the sudden fault of transmission parts in high speed wire rolling mill, the fault diagnosis based on the vibration measurement is an effective method.
针对高速线材轧机传动零部件的突发故障，开展基于振动测试的故障诊断研究可以有效加以避免。
The technology, equipment and technical parameters of high speed wire-rod mill in Zhangjiagang, with the highest technical level in the world, are introduced.
介绍了具有当前世界线材轧机最高水平的张家港高速线材轧机的工艺、设备情况及主要技术参数；
The method and example of pass optimization design of high speed wire rod finishing mill by dynamic programming with minimum total tension coefficient are described.
阐述了以动态规划法按最小总张力系数对高速线材轧机精轧机组孔型进行优化设计的方法与实例。
In high speed wire-rod mill, guide roller is the main consumption tool, excellent wear resistance, adhering steel resistance and hot fatigue resistance are required.
导辊是高速线材轧机上的主要消耗工具，要求高耐磨性、抗粘钢性和热疲劳抗力。
The advanced development process flow of "converter-small billet continuous casting machine-high speed wire rod mill" is adopted in developing EH14 wire rod for weld.
青钢应用“转炉-小方坯连铸机-高速线材轧机”工艺流程试制EH14焊接用钢盘条。
The purpose of the controlled-rolling and controlled-cooling technique and the application characteristic and tendency in links of production of high speed wire are introduced.
介绍了线材控制轧制和控制冷却工艺的目的，控制轧制和控制冷却在高速线材生产过程中各个环节的应用特点及发展趋势。
The characteristic of roll pass system in high speed wire mill was introduced, moreover, the deformation parameters and variation regular pattern of the roll pass were analyzed.
介绍高速线材孔型系统的特点，并对其变形参数及其变化规律进行分析。
The Load-Commutated Inverter(LCI) fed synchronous motor control system which is applied to the main drive for high speed wire finishing mill of Baotou Iron and Steel Co is presented.
介绍了用于包钢高速线材厂精轧机主传动中的负载换流同步电动机控制系统。
To introduce the trial production process of ML08Al cold heading steel adopting the process of converter steel-making, LF refining, billet continuous cast and high speed wire rod mill.
介绍采用转炉、l F炉精炼、小方坯连铸机、高速线材轧机生产工艺试制ML 08 A l冷镦钢的过程。
The Low tension control is successfully accomplished in the roughing and intermediate mill of the high speed wire rod mill at Tangshan Iron and Steel co., and a good effect is obtained.
在唐钢高速线材轧机中，成功地实现了粗轧机和中轧机的微张力自动控制，取得了良好效果。
An analysis is made on cause of the damage incident of quick fuses, controlled silicon and power control panels of the DC driving devices of Chuanwei High Speed Wire Plant due to overvoltage.
分析了因过电压造成川威高线直流传动装置快速熔断器、晶闸管及电源控制板损坏事故的原因，认为直流传动装置过电压保护措施必须完善，不能随意拆除。
The paper introduces the course of production and development on free cutting steel wire at High Speed Wire Rod Mill. The problems are analyzed during production and the measures have been taken.
简述了高线厂易切削钢丝的生产开发过程，分析了生产中出现的问题，以及采取的措施。
When taking compact mill as rough stands of high speed wire mill, the tensile force for biting and stable rolling are different, resulting in the dimension variation at end and middle part of product.
以紧凑式轧机作为高速线材粗轧机组时，由于粗轧中各机架咬入和稳态轧制的张力不同，致使坯料出口头尾尺寸波动较大。
Hardware-accelerated high performance, multi-step, wire-speed message processing for XML -, XSLT -, and XPath-based transformations and XML schema validation.
通过硬件加速为基于XML、XSLT和XPath的转换和XML模式验证实现高性能、多步和快速消息处理。
The influence of peak current on finishing high-speed wire electrical discharge machining (WEDM) in gas and emulsion dielectric is studied.
研究了在大气和乳化液两种介质中，峰值电流对高速走丝电火花线切割加工的影响。
Manufacturing sector is divided into high-speed wire moving shop, low-speed wire moving shop, grinning shop, composing shop and CNC processing shop.
制造部门拥有快走丝车间、慢走丝车间、磨床车间、组装车间、CNC加工车间。
The main factors that affect the machining precision and surface quality in high-speed wire cutting are analyzed. And the corresponding effective precautionary measures and handling methods are given.
分析了高速走丝线切割加工中影响加工精度与表面质量的主要因素，并针对这些原因分别给出各自有效的预防及处理方法。
应用推荐