The clearance variation that is caused by the heat deformation of the cylinder and the plunger piston is analyzed.
材料及气缸和柱塞间的配合间隙等问题进行了分析研究。
The relationship of the heat deformation processes of the antirust aluminum alloy LF6 and its microstructure were studied.
研究了防锈铝合金LF6热变形工艺对组织的影响。
The results show that microstructure and mechanical properties of the BTi-62421S alloy can be significantly improved by heat deformation.
结果表明，热变形能明显优化合金的组织和力学性能。
The technological parameter of heat deformation was confirmed by the test of Upsetting technology, and the isothermal stamping was studied.
通过镦粗工艺试验，确定了该材料的热变形工艺参数，并对其进行了等温模锻工艺研究。
In this paper, calculation programs of planar stationary temperature field and heat deformation for spindle box of general lathe are developed.
本文应用有限元法编制了计算程序，在微型机上对机床主轴箱箱壁进行了平面稳定温度场及热变形的理论计算。
The DMA analysis indicated that radiation crosslinking raised heat deformation temperature of PCL and caused a rubbery state after the melting of PCL crystals.
DMA分析表明，聚己内酯辐照交联后的弹性模量和耐热性能显著提高。
The effect of organic rectorite on the viscosity, gel-time, heat deformation temperature, mechanical properties and wet-heat resistant property were researched.
分别研究了有机粘土对树脂体系粘度、凝胶特性、力学性能和热变形温度、耐湿热性能等的影响。
The results show that the addition of mica can enhance the flexural strength, flexural modulus, notched Izod impact strength and heat deformation temperature of the composites;
结果表明：云母可有效提高PP的弯曲强度及模量、悬臂梁缺口冲击强度和耐热性能；
The results of experiments show that tensile strength, bend strength, bend modulus and heat deformation temperature of the composite materials are increased with the increase of carbon fibre content.
随碳纤维比例的增大，该复合材料的拉伸强度、弯曲强度、弯曲模量及热变形温度均呈上升态势；而缺口冲击强度及击穿电压呈下降态势。
And in general the rod gets hot, and the work that you have done goes into heat and goes into the deformation of the rod.
通常棒子会变热，你做的功，变成热能，导致棒子的变形。
When need long time stop outdoor conditions, the vehicle should avoid direct exposure in the sun, to prevent the door seals, skylight on the edge of the deformation and cracking due to heat.
当遇到需要长时间停靠户外的情况时，车辆应尽量避免直接在阳光底下暴晒，以防止车门、天窗边上的密封圈因受热而发生变形和龟裂。
This not only increase productivity, and cut parts can reduce the deformation and cut the heat affected zone seam.
这不仅提高生产率，而且能减少被割零件的变形量和割缝区的热影响区域。
All reworked surfaces must be shot-peened after removing material damaged by corrosion, heat, and deformation.
所有的翻修表面在去除腐蚀、受热和变形材料后必须进行喷丸。
The formation of roll-casting microstructure is mainly attributed to the deformation of un-solidified liquid phase, the varied distribution of mass and heat.
铸轧组织的形成主要是变形作用于未凝固的液相，引起质量和热量的分布状态发生改变所致。
Consider and prevent the product deformation caused by thermal stress release in the process of heat treatment.
预估及预防在热处理过程中因热压释放导致的产品变形。
No heat build up or deformation provides high precision accuracy.
没有热变形提高了高精度的准确性。
Heat generation and deformation are key factors that influence the rigidity and machining accuracy of the high-speed precision spindle system.
轴承的发热变形是影响高速精密主轴系统刚度和加工精度的重要因素。
Than the loose organization of the abrasive used is not easy passivation, less heat in the grinding process can reduce the workpiece deformation and heat burns.
较松组织的磨具使用时不易钝化，在磨削过程中发热少，能减少工件的发热变形和烧伤。
Temperature field distribution of weldment, which reflects complex welding heat process, is a basic on studying welding deformation, residual stress and so on.
焊件中的温度场分布反映了复杂的焊接热过程，是研究焊接变形、焊后残余应力等状况的基础。
Strengthen the floor in the heat is not deformation, in this area is also better than solid wood flooring composite floor.
强化地板在受热方面不变形，在这方面也比实木地板复合地板要好。
After deformation and heat treatment, single crystal al wire will generate a mass of dislocation cells, high density dislocations and evident recovery phenomena.
单晶铝线材在变形和加热后会产生大量的位错胞、高密度位错和明显的回复再结晶现象。
Improvement of elongation of joint is related to weaker cool deformation degree of heat affect zone (HAZ) and uniformity of strength and stress level between weld and base metal.
接头延伸率的改善同热影响区冷变形程度的减弱及焊缝强度、应力水平同母材趋于一致有很大关系。
Cold deformation and heat treatment have been studied through testing mechanical property and conductivity of Cu-Cr alloy, and strengthening mechanism has been presented in the paper.
通过测试力学性能和导电性能，对铜铬合金进行了冷变形及退火工艺的探索，并进行了强化机理分析。
The motions, deformation and heat transfer characteristic of a rising gas bubble through the liquid in a vertical channel are numerically predicted in this paper.
用数值方法模拟了竖直通道宽度对气泡在液体中的非定常运动、变形以及传热特性的影响。
For tensity disposal of saw blade, the cutting heat was considered when analysing the stress and deformation of the new combined diamond saw blade by applying ANSYS.
针对圆锯片基体的适张处理，在考虑切削热影响的情况下，应用ANSYS对新型组合式金刚石圆锯片基体进行应力、变形分析。
Stress wave energy is dissipated in form of heat and plastic deformation energy.
应力波能量主要是以热能和塑性变形能耗散。
Matchine parts, choose quality stell, the heat treatment of high strength never deformation.
机床部件， 剪板机选用优质钢材，经高强热处理永不变形。
Matchine parts, choose quality stell, the heat treatment of high strength never deformation.
机床部件， 剪板机选用优质钢材，经高强热处理永不变形。
应用推荐