Among these properties, mechanical properties such as hardness and modulus are substantial and of great importance.
在材料的诸多性能中，硬度是其最重要、最基本的性能指标之一。
The results show that the hardness and elastic modulus increase as the sputter power increases.
经实验结果显示其硬度与弹性模数皆会随著溅镀功的增加而增加。
But the optical surfacing on SiC mirrors is extremely difficult because of its high hardness and elastic modulus.
但是，由于碳化硅材料所具有高硬度、高弹性模量等性质，使碳化硅质反射镜的光学加工难度很大。
In situ imaging nanoindentation was used to characterize the differences in longitudinal Modulus of Elasticity (MOE) and hardness of different cell wall layers of softwood tracheids.
该文利用原位成像纳米压痕技术研究了针叶材管胞细胞壁不同壁层之间在纵向弹性模量(MOE)和硬度方面的差异。
The results indicate that microcrystalline deposit with low phosphorus content has higher hardness, modulus and fatigue resistance than the amorphous deposit with high phosphorus content.
结果表明，低磷微晶镀层较高磷非晶镀层具有更高的硬度、弹性模量和疲劳抗力；
Ebonite is one kind of special rubber product with high strength, high modulus, high hardness and fine unnotched impact resistance.
硬质橡胶是一种具有高强度、高硬度、高模量以及良好无缺口抗冲击强度的特种橡胶制品。
The tensile strength, modulus of elasticity(MOE) and hardness of Pinus massoniana fibers were determined by using zero-span tension and nanoindentation technique.
研究了人工林马尾松的纤维零距抗张强度、细胞壁的纵向弹性模量和硬度等力学指标。
The nano-indentation results show through changing the deposited voltage and C_2H_2 gas flux rate could increase the hardness and elastic modulus of the films.
纳米压痕试验结果表明，通过改变沉积负偏压和C_2H_2流量可以提高薄膜的硬度和弹性模量。
Results showed that as the hardness of modified EPDM increased the brittle-ductile transition moved to high rubber contents and the flexural modulus increased profoundly, however.
结果表明：随着EPDM硬度的增加，共混物不仅韧性提高，弯曲模量也大幅度上升。
Nanoindentation has been widely used to evaluate and test material properties, we utilize the unloading curves of an indentation test to extract the hardness and reduced modulus of the material.
纳米压痕技术广泛用于材料力学性能的评估与测试，利用压痕的加卸载曲线可分析得到材料的硬度和折合模量等力学参数。
The hardness and elastic modulus of the alloy were investigated by means of nano-indentation technology.
利用纳米压入测量仪测试了不同组织结构下的硬度和弹性模量。
The hardness, Young's modulus, wear resistance, and corrosion resistance of the coating are higher due to the recombination action of amorphous and inter-metallic compounds.
在非晶相和金属间化合物复合作用下，复合涂层具有高的硬度、弹性模量、耐磨性和耐蚀性。
The results showed that the filling of short fiber evidently improved tear strength, modulus at 10%and Shore A hardness of SFRC.
结果表明，短纤维的加入显著提高了SFRC的撕裂强度、10%定伸应力及邵尔A型硬度；
With the increase of DCP content from 0.2~1.0 phr, the modulus, hardness and elastic modulus ( E ′) of SBR vulcanizates increase but the tensile set at break decreases.
结果表明，DCP用量在0 .2～ 1 .0份时对硫化胶的抗张强度影响不大，但是远远大于未硫化橡胶的强度；
The results showed that the high carboxylated NBR featured high hardness, tensile strength and modulus, good abrasion resistance, but greater permanent set and poorer processing safety;
结果表明，高羧基丁腈橡胶具有硬度、拉伸强度和定伸应力高，耐磨性好，压缩永久变形大，加工安全性较差等特点；
Meanwhile, the phase transition temperature, micro-hardness and elastic modulus were analyzed by DSC, nano-indenter and the other instruments.
同时，采用DSC和纳米压痕仪等仪器，测试薄膜的相变温度、显微硬度和弹性模量。
Meanwhile, the phase transition temperature, micro-hardness and elastic modulus were analyzed by DSC, nano-indenter and the other instruments.
同时，采用DSC和纳米压痕仪等仪器，测试薄膜的相变温度、显微硬度和弹性模量。
应用推荐