About half of all aluminium castings are made using high-pressure die-casting (HPDC), in which a molten aluminium alloy is injected under pressure into a steel mould, or die.
大约有一半的铸铝工艺是高压模铸(HPDC)，在这种工艺中，通过压力将液态铝合金注入钢模，或模具。
One half of the negative mould and the 'inside of the crankcase' mounted.
其中一半的负面模具和'内的曲轴箱'展开。
Thee difficult part about the milling is that you will have to do this also in the other half of the mould and there everything should be mirrored.
困难的一部分，约铣削的是，你将不得不这样做也有另一半的模具和有一切应镜像。
There is not so much to mill (not so deep) and it only has to be done twice (this half of the mould and the other half of the mould).
有没有这么多磨(不如此之深)，它不仅需要做两次(这一半的模具和另一半的模具)。
Photographed every day for the past half a year by Manhattan artist Sally Davies the kids meal of fries and burger is without a hint of mould or decay.
曼哈顿艺术家莎莉·戴维斯在过去的半年每天都拍摄照片，儿童套餐薯条和汉堡一点也没有发霉或腐烂。
An injection mould with half-parting inlaying structure was developed based on the analysis on forming process of wiring terminal positioning fixture with nine-thread pedestal.
通过对九线基座、接线柱定位夹具注射模镶件的工艺分析，确定了成型镶件分半镶拼式结构。
As a result, a mould with double stripper mechanism was needed, that is to say, there were levers and ejector pins on the stationary mould half and ejector pipes on the moving mould half.
为保证顺利脱模，模具设计采用了双脱模机构，即定模采用杠杆、推杆顶出机构，动模采用推管二级顶出机构。
The non-sinusoidal mould oscillation of machine was simulated at a half plank spring mould tester. The developed hydrauli…
在半板簧结晶器振动试验装置上，模拟了小方坯连铸机的非正弦振动。
The non-sinusoidal mould oscillation of machine was simulated at a half plank spring mould tester. The …
在半板簧结晶器振动试验装置上，模拟了小方坯连铸机的非正弦振动。
This has to be done also in the other half of the mould and later when you make the WAX crankcases you can see how exactly it was.
这需要做也有另一半的模具，后来当您使蜡曲轴箱，你可以看到如何，正是它。
In the design of the plastic mould, a latch_lock mechanism was designed to transfer the machine driving force from the moving half to the fixed half to make the ejection system of the fixed half work.
在塑料模具设计中，设计一种延时脱开机构将机床动力由动模传递给定模，使定模顶出机构工作；在侧抽芯机构中设计出一种顶出机构，改善塑件的成型质量，防止塑件脱模时的变形。
The examples listed have certain reference value to the location of the mould cores for other-type products and even to the location of various inserts of the fixed half and movable half of moulds.
所举的实例对其它类型产品的型芯以至于扩展到各种定、动模镶件的定位结构具有一定的参考意义。
Resin sand mould was adopted with precoated sand core. The upper and bottom half boxes used horizontal pouring design with box middle line as parting face.
采用树脂砂砂型、覆膜砂砂芯，上、下两个箱体均采用平做平浇的工艺方案，并选取箱体中线为分型面。
Resin sand mould was adopted with precoated sand core. The upper and bottom half boxes used horizontal pouring design with box middle line as parting face.
采用树脂砂砂型、覆膜砂砂芯，上、下两个箱体均采用平做平浇的工艺方案，并选取箱体中线为分型面。
应用推荐