The relationship between three-dimensional grain morphology characteristics and random cross-sectional parameters has been established based on the method of simulation slicing.
本文通过仿真切割的方法建立晶粒三维空间形貌特征与其随机截面形貌参数之间的关系。
Scanning electron microscope (SEM) and X-ray diffraction (XRD) were used to measure the surface morphology, the crystal microstructure and the distribution of diamond grain in the film.
用扫描电镜(sem)和X射线衍射(XRD)方法检测了复合膜的表面形貌、晶体显微结构和复合膜中金刚石颗粒的分布情况。
This paper advanced a study method that can observe plastic deformation behavior of surface layer of die cavity by showing austenite grain, size, crack morphology and propagation mode.
提出了通过显示奥氏体实际晶粒度、裂纹形貌和扩展方式来分析热锻模具型腔表层塑性变形行为的试验方法。
Grain size analysis also indicates that grain size characteristics are mainly influenced by intensity of erosion or deposition and morphology of windward slope.
粒度分析也表明，沙丘迎风坡表面粒度特征主要取决于表面蚀积状况，同断面形态表现出密切的相关性。
SEM experiment displays that the deposit has a (surface) morphology of granular structure with uneven grain sizes.
SEM实验表明，镀层表面形貌为团粒状，颗粒大小较不均匀。
The morphology of the powders was studied by SEM and EDS, on which the discussion of grain refinement mechanisms is based.
利用SEM和能谱分析，研究了其微观形貌的变化，并对球磨粉末的晶粒细化机理进行了一定的研究。
The results of SEM, TEM, SAED and XRD show that the direction of gas current and the physical or chemical changes of catalyst grain cause the morphology variety of carbon micro-coils.
结果表明，反应气流的流向以及催化剂在反应过程中发生的物理和化学变化是导致碳微线圈形态变化的两个重要原因。
Then the morphology was observed by optical microscope and SEM. The grain size of austenite, the number of martensite in austenite grains and the spacing of the lath martensite were measured.
用金相显微镜和SEM观察了试样铸态微观组织形态，测定了奥氏体晶粒尺寸以及奥氏体晶粒内马氏体板条束个数和马氏体板条间距。
The results show that alloying elements and rare earth can refine grain, change carbide morphology and distribution, and increase mechanical properties and wear-resistant properties.
结果表明，合金元素能够细化晶粒，改善碳化物的形貌和分布，提高力学性能和耐磨性。
SEM and AFM studies show that surface of the C60 film is very flat, arrangement of crystalline grain is even, morphology of C60 crystal is sharp.
薄膜的SEM和AFM观测表明样品表面光滑，且呈现出形态完整、分布均匀的晶粒。
It is shown that the zigzag grain boundary may delay the initiation, growth and propagation of crack, as well as may also influence the crack morphology and the fracture mode markedly.
研究表明，弯曲晶界对裂纹的萌生、长大及扩展，对裂纹的形态及断裂方式，都有显著的影响。
Intergranular corrosion resistance was increased owing to the lessening of carbide particles formed at austenite grain boundaries and morphology changing from reticular to granular.
与不加稀土时相比，焊缝中沿晶界析出碳化物的尺寸减小、数量减少、析出形态由网状析出变为不连续的颗粒状，抗晶间腐蚀能力得到提高。
The relative amount of IAF and the morphology of grain boundary ferrite in HAZ were the decisive factors affecting the strength and toughness of HAZ.
HAZ组织中IAF相对数量及晶界铁素体的形态是影响HAZ强韧性的决定性因素。
The results show that the grain is fined, the morphology of reticulation carbides is improved, the hardness and wear resistance of casting high speed steels are also enhanced by modifying treatment.
研究了热处理工艺对铸态和变质处理铸造高速钢组织与性能的影响。
The results show that the grain is fined, the morphology of reticulation carbides is improved, the hardness and wear resistance of casting high speed steels are also enhanced by modifying treatment.
研究了热处理工艺对铸态和变质处理铸造高速钢组织与性能的影响。
应用推荐