The main wiring uses the single generatrix emanant wiring plan.
主接线采用单母线放射式接线方案。
The temperature in generatrix layer is higher than in the worm wheel layer.
母线层的温度较高，而蜗壳层的温度较低。
We need to consider the deformation of only one strip parallel to generatrix of the cylinder.
我们只需要考虑一个平行于圆柱母线的窄条的变形。
The key point for re-constructing rotation surface is setting up rotation axis and generatrix.
旋转面重建的关键是确定旋转轴和母线。
A conic section whose plane is not parallel to the axis base or generatrix of the intersected cone.
圆锥的一部分，其切面既不平行于轴和基面，也不平行于圆锥母线。
There are mainly four parts in the new type data collection system: generatrix signal collection device;
本文设计的新型数据采集系统主要包括四个部分：母线信号采集装置；
Straight generatrix shape roller and arc generatrix shape roller are incompletely the same in processing.
形母线与圆弧形母线滚子，在采用无心贯穿磨削时，并不完全相同。
A novel supersonic induction heating supply is researched, which is suitable for large-area generatrix brazing.
对高频感应加热电源中的线圈进行了研究与设计。
Because most firebox generatrix is composed of complex curves, it is very difficult to get CNC cutting program with manual means.
由于燃烧室外表面的母线轮廓复杂，手工编制数控加工程序难度大。
According to the restriction of the generatrix line Bertrand surface can be constructed with the Bertrand curve with broad sense group.
按照母线的约束，形成广义白川德曲线族，进而构造出白川德曲面。
According to the restriction of the generatrix line, Bertrand surface can be constructed with the Bertrand curve with broad sense group.
按照母线的约束，形成广义白川德曲线族，进而构造出白川德曲面。
In this paper, the axial section profile of worm with straight generatrix is analyzed and calculated according to Angle projection calculating.
本文利用角度投影计算法对直纹蜗杆轴向齿形进行了分析与计算。
In order to avoid power cut during examining and repairing of generatrix or conk out of this operation mode, breaker can be used to separate mono generatrix.
为了避免这种运行方式在母线检修、故障时可能造成停电的缺点，因此可用断路器将单母线分段。
Transformer substation including each kind of equipment: transformer, circuit breaker, load switch, generatrix, current transformer, voltage transformer and so on.
变电站包括各类设备：变压器、断路器、负荷开关、母线、电流互感器、电压互感器等。
Formula to evaluate translation of the tooth-surface and the equation to describe the generatrix of the negatively cambered sooth-surface were derived respectively.
分别推导得到齿面平移距离和内凹齿面母线方程的计算公式。
Taking the straight-line-rack as the tool the error of straight generatrix is measured and by error analysis the tooth profile error and tooth orientation error can be obtained.
以刃边齿条为工具，测量廓面的直母线族误差，通过误差处理与分析获得齿廓总偏差和螺旋线总偏差。
The former is similar to bulge, but the deforming mode of the latter is rolling in which the stress is tensile in generatrix direction and the wall thickness are mainly reduced in this zone.
前者的受力情况类似于胀形，后者为母线方向拉应力作用下的辗压变形，该区起主要减薄壁厚的作用。
This paper analyzes emphatically the feature that the workpiece is located on the V-shape block by outside column surface, and discusses relation of rotor line between outer circle generatrix.
分析工件以外圆柱面在V形块上定位的特点，明晰工件回转轴线和外圆母线之间的关系。
Adopting the engaging process of the measuring rack - probe, the error of straight generatrix is measured, and by error analysis, the tooth profile error and tooth orientation error can be obtained.
采用刃边齿条测头，测量齿轮廓面的直母线偏差，通过误差分析分离出齿廓总偏差和螺旋线总偏差。
Adopting the engaging process of the measuring rack - probe, the error of straight generatrix is measured, and by error analysis, the tooth profile error and tooth orientation error can be obtained.
采用刃边齿条测头，测量齿轮廓面的直母线偏差，通过误差分析分离出齿廓总偏差和螺旋线总偏差。
应用推荐