The drive gear is selectively movable along the drive gear axis.
所述传动齿轮沿所述传动齿轮轴可选择性地移动。
This paper mainly performs the design and mechanical analysis and research on cold extrusion mold of the gear axis in cars.
本文主要对汽车用齿轮轴的冷挤压模具进行了设计和力学分析研究。
Precision machining pump body can make "d" type bearings and gear axle, ensure accurate gear axis gear eccentric wear, not to.
精密加工的泵体可使“D”型轴承与齿轮轴精确配合，确保齿轮轴不偏心，以防齿轮磨损。
This paper deals with the cause of crack appearing on main landing gear axis. It shows that the cracks belong to the grinding ones.
本文对主起落架轴裂纹产生的原因进行了分析，裂纹为磨削裂纹。
According to the relative position of sub-gear axis parallel shaft spur gear drive, bevel gear drive shaft and intersecting cross-axis helical gears.
按齿轮轴线的相对位置分平行轴圆柱齿轮传动、相交轴圆锥齿轮传动和交错轴螺旋齿轮传动。
The preselection machine of gaskets is used for selecting the adjusted gaskets in assembling the initiative taper gear axis of the automobiles driving axle.
主齿垫片预选机主要用于汽车驱动桥主动锥齿轮总成装配时选择调整垫片，调整垫片厚度对圆锥滚子轴承的轴向力分配有很大影响。
The advantage of the gear axis with cold extrusion technology replacing metal cutting working production are narrated, and the technological analysis for the gear axis part is conducted.
叙述了采用冷挤压工艺代替切削加工生产齿轮轴的优点，并对齿轮轴零件进行了工艺分析。
Rationally define the work gear pump speed, gear and the axis of rotation to avoid engaging resonance frequency, can prevent noise intensified.
合理确定齿轮泵的工作转速，使齿轮与轴的转动避开啮合共振频率，可以防止噪声加剧。
This paper brings out feasibility and applicability to make change drive of double step sliding gear by moving one gear width along axis under conditions of Corresponding ratio of gear.
本文阐述了双联滑移齿轮在适当传动出情况下，轴向移动一个齿轮宽度就可以进行变速的可行性及适用场合。
No beat or squeeze when connect load to the outer axis of gear speed reducer so that not to arise deformation and dislocation, bad noise or locked dead.
齿轮减速器的出轴与负载连接时不能重力敲打、挤压，以免造成内部变形走位，产生严重噪声或卡死现象。
The new method without movement paralleled with the axis of the gear makes the lead error measurement can share same generating system with profile measurement.
此方法不需要测头沿齿轮轴线方向的运动系统，利用齿形测量系统即可测量齿向误差。
HC Series, CNC Hydraulic Coupling gear indexing Tables (4th axis, non-lifting type), the standard model are every 1 and 5 degrees indexing (72d and 360d).
HC系列，液力偶合器齿轮数控分度表(第4轴，非提升式)，标准模型，每1和5度索引(72d和360d)。
It is very useful to analysis the affection of crown gear coupling and correspond axis by addition moment of bending in engineering.
对工程中分析弧形齿联接轴及其相应轴段所受弯矩的影响具有重要参考价值。
YCB arc gear pumps are mainly gear, KCG axis, the pump body, cover, the axial bearing, sealing etc. Using double circular-arc gear tooth sine curve.
主要有齿轮、轴、泵体、泵盖、轴承套、轴端密封等组成。齿轮采用双圆弧正弦曲线齿形制造。
This subject is about thermal deformation error detection and compensation of an YKX3132G six axes CNC gear-hobber machine's worktable in X axis direction.
本课题针对在KX3132G型六轴数控滚齿机床加工过程中，工作台热致变形产生的X轴方向上的误差进行测量与补偿。
Tthe mixer is primarily composed of mixing silo, mixing axis and their axle end seal device, main drive gear and discharging mechanism etc.
该搅拌机主要由搅拌筒体、搅拌轴及其轴端密封装置，以及主传动机构和卸料机构等部分组成。
The dynamic mechanism of a new type of machine tools for machining plane is discussed, which is the roulettes of the fixed axis gear train.
探讨了一种新型车削平面运动机床的运动机理，即定轴轮系的旋轮线原理。
Fluctuation axis adopt high precision screws spin umbrella gear rotating.
上下轴采用高精度螺丝旋伞齿转动。
According to the fundamentals that pure-rolling must take place between the pitch line of hob and the pitch curve of gear workpiece, the 4 axis complicated simultaneous-control relation was obtained.
从滚刀节曲线与齿轮工件节曲线之间必须进行纯滚动出发，推导出联动关系为4个坐标的复杂联动。
Based on the conceptual model of the five-axis simultaneous CNC bevel gear cutting machine, a new machining theory for the function-oriented active tooth surface of hypoid gear is proposed.
基于五轴联动数控铣齿机的概念模型，提出一种新的加工准双曲面齿轮主动设计齿面的切齿原理。
The expression of the axis section profile of grinding wheel used to machine double-circular-arc gear is derived in detail. And the general calculator program is developed.
本文详细地推导出加工双圆弧齿轮的砂轮截面廓形的计算表达式、并研制了通用的计算程序。
There are built with a worm gear drive which has proven to be kinematically ideal for fast bi-directional rotation, Rotary axis is driven with gears via Servo motors.
存在与蜗轮传动的运动学已经被证明是快速的双向旋转的理想建成，旋转轴是通过伺服电机驱动，齿轮。
The key to fine machining gear by profile grinding method is how to calculate and shave the axis section profile of grinding wheel.
成形磨削法精加工齿轮的关键在于修整砂轮的截面形状。
A screw gear type differential mechanism includes a differential carrier, an operculum, a main reducing gear driven gear, left and right half axis gears, etc.
本螺旋齿轮式差速器，包括有差速器壳、壳盖，主减速器从动齿轮，左右各一个半轴齿轮等。
It is shown that S-H crossed-axis helical gears perform a good gear transmission on condition of little axial Angle.
H交错轴斜齿轮传动是小轴交角情况下空间交错轴传动的一种优良形式。
By studying the transformation principle of the machining setting parameters from cradle style machine to CNC gear generator, mathematical kinematic models of every axis are deduced.
通过对螺旋锥齿轮机械式铣齿机与CNC铣齿机之间加工调整参数转换原理的研究，推导了这两类机床运动轴数学模型；提出了求解各运动轴表达式系数的速度求导法。
The formulas for calculating 3-axis, double composite gear with addendum modification are derived. Then in this paper the object functions -and restrained conditions for optimum design are discussed.
本文推导了采用修正齿轮时三轴双公用齿轮机构的计算公式。并讨论了双公用齿轮机构优化设计的目标函数和约束条件。
The main production process all kinds of gear, worm gear, sprocket, spline, the long axis, filament rod mechanical parts.
主要制作加工各类齿轮、蜗轮、链轮、花键、长轴、长丝杆等机械配件。
The main production process all kinds of gear, worm gear, sprocket, spline, the long axis, filament rod mechanical parts.
主要制作加工各类齿轮、蜗轮、链轮、花键、长轴、长丝杆等机械配件。
应用推荐