Generally, the cylinder and the cylinder head bolt together with a thin gasket pressed between them to ensure a good seal.
一般来说，气缸和气缸盖用螺栓紧固在一起，气缸与气缸盖之间用一薄垫圈确保密封良好。
To prevent this from happening, avoid excessive tightening force and install a new gasket with every cylinder change.
为了防止这种情况发生，避免用过大的上紧力，并且每次换钢瓶的时候装一个新的垫圈。
Increasedcondensation by short distance driving below 20 km or a defect in the watercircuit (cylinder head gasket or flange connections) with entry of coolingwater.
由于低于20公里的短途行驶或者因为冷却系统（汽缸垫或法兰连接）的缺陷让冷却水进入，导致冷凝水增加。
In order to meet steady compression -resilience properties as cylinder gasket, the thickness tolerance of composite sheet and the density of flexible graphite plate should be control.
为了满足汽缸垫稳定的压缩、回弹性能要求，应注意复合板的厚度公差和柔性石墨面材最佳的密度范围的控制。
The features and principles of the double tightening method for cylinder head bolts is introduced to insure the uniform pressure on cylinder gasket during assembling operation.
介绍了装配作业中可确保发动机气缸盖全部螺栓对气缸垫压力均等的二次紧固的特点和原理。
The results expatiated that the strength of such cylinder head gasket meet the need when being used.
结果表明，此气缸垫的强度满足使用要求。
Company founded in 1965, lies in xiangshan byland ningbo, covering 6500 square meter. specialized in the design, development, production and distribution of all kinds cylinder gasket of gas engine.
公司创建于1965年，坐落在宁波市境内的象山半岛，占地面积6500平方米，是一家专业设计研制生产销售各类内燃机气缸垫片的企业。
The cylinder gasket is an important sealing part of engine.
气缸垫是发动机的重要密封件。
An engine cylinder head gasket leaking between a cylinder and an adjacent water jacket is indicated by coolant foaming or overheating and loss of coolant.
在一个汽缸和相邻的水套之间的引擎汽缸头套环泄漏的标志是冷却液冷却液产生泡沫或者过热，并且冷却液流失。
The acquirement of accurate 3D measurements of the engine cylinder gasket is the key of quality control and reverse engineering.
发动机气缸垫精确三维尺寸的获得是气缸垫质量检验及其样品反向工程的关键。
Teflon - lined pipe, casing, elbow, the three exchanges or four, size head, cylinder, air compressor - oxygen - ring, gasket seal ring and auto parts.
聚四氟乙烯内衬直管，套管，弯头，三通，四通，大小头，筒体，空压机-制氧机-活塞环、密封圈和汽配封圈。
Carburetor gasket seal, small general gasoline engine sealing, air filter separator device sealing, sealing, crankcase sealing, cylinder head gaskets, insulation gasket, exhaust pipe sealing.
小型通用汽油机用垫片，化油器密封，隔板器密封，空气滤清器密封，曲轴箱密封，汽缸头垫片，隔热罩垫片，排气管密封。
The initial demand-driven gasket tighten the cylinder head of the Rolls-Royce Merlin engines.
最初的需求驱动需要的垫圈准确地收紧了罗尔斯罗伊斯的默林发动机的气缸盖。
Adopt integral cylinder gasket to greatly enhance reliability and to fully avoid punch.
采用整体式汽缸床，可靠性大为提高，完全避免冲床。
Adopt integral cylinder gasket to greatly enhance reliability and to fully avoid punch.
采用整体式汽缸床，可靠性大为提高，完全避免冲床。
应用推荐