When equipment slotted side gap, face plate electrode and groove, perpendicular to the bottom of the shell and necessary.
当设备有槽侧的隔阂时，面临电极板和槽，壳有必要垂直于底部。
The process of dielectric breakdown in uneven electric field is analyzed and the influence of electrode polarity on gap breakdown is researched.
文中分析了在极不均匀电场下间隙的击穿过程，并用试验研究了微细加工时电极极性对间隙击穿电压的影响。
The influence of laser sampling, auxiliary spark discharge voltage, and electrode point gap on analytical results was examined.
考察了激光取样、辅助火花放电电压、电极尖端距离等条件变化时对分析结果的影响。
In this paper, some new points were put forward based on theoretical analysis of the discharge gap of Electric discharge Generating machining based on wire electrode.
针对基于线电极展成加工的放电间隙进行了理论分析，提出了一些新的研究观点。
Effect of electrode insulation on the electric field and the flow field of the machining gap during electrochemical drilling (ECD) is numerically studied.
通过对孔电解加工中加工间隙的电场和流场仿真，研究了电极绝缘层的涂覆尺寸特征对小孔加工性能的影响。
It indicates that the rotary-arc gap switch employing a sharp knife-edge electrode as a third trigger electrode can distinctly reduce the electrode erosion and prolong the lifetime of the switch.
在不同开关结构、不同电极材料和不同电流波形情况下对开关进行了单次触发放电实验，验证了旋转电弧、场畸变间隙开关能够有效地减轻开关电极的烧蚀程度；
The gap allows a stress-compensating deformation of the projecting electrode relative to the substrate.
该间隙允许凸出电极相对基片发生应力补偿形变。
The dimensional accuracy of electrical discharge machining(EDM) is greatly influenced by the overcut resulting from the discharge gap and electrode wear.
电火花加工工件的尺寸精度受过切量影响，而过切量的大小主要取决于放电间隙和电机损耗。
The results show that the long electrode gap leads to the positive column which is caused by the climbing voltage on the cathode surface due to the accumulation of positive ions.
结果表明，放电单元采用大电极间距可获得正柱区放电，正柱区的形成是正离子在阴极鞘层区不断积累将电位抬高所致。
The breakdown voltage of air gap increases with the electrode spacing increasing.
电极间距增大后，气隙的击穿电压增大。
The system's main functions are: testing the defects of the transparent electrode and recording the position of defects, measuring the widths of the transparent electrode and the discharge gap.
系统的主要功能为：透明电极的缺陷测量与定位和透明电极宽度与间隙测量。
The delay and jitter characteristics of the three electrode spark gap weres studied in this paper.
研究了三电极球隙的延迟和抖动特性。
The relation between relative light crosstalk and driving voltage, gap of discharge electrode, width of electrode, as well as the effect to restrain crosstalk with barrier ribs are also discussed.
着重讨论了相对光串扰与驱动电压、放电电极间距、电极宽度之间的关系。
Such horizontal magnetic field will make the arc move out of the electrode gap, and reduce the interrupting ability of the vacuum interrupters.
这一横向磁场会将电弧吹向弧隙外侧，削弱了真空灭弧室的开断能力。
Based on the model, the relationship between the main pulse frequency of supply power and the balanceable inter-electrode gap is discussed.
给出了脉冲电化学加工极间平衡间隙的数学模型，并据此讨论了高频群脉冲电化学加工中，电源主脉冲频率与平衡加工间隙的关系。
The synthesizing control scheme is put forward based on the requilement of narrow-gap all-position welding technology in terms of the moving track of tungsten electrode.
在厚壁管、压力容器及电站锅炉的窄间隙全位置焊接中，钨极运动轨迹是动态的。
And the static self-breakdown of the switch indicates that after electrode optimization the static self-breakdown voltage is stable and the distribution of electric field in the gap is mostly uniform.
开关进行了静态自击穿实验，实验结果表明开关静态自击穿电压是比较稳定的，同时也说明所研制的开关间隙内部电场分布比较均匀。
A circular tube-like gap (S1) in which a plating liquid (17) flows is formed between the tubular electrode placed in the hollow section and an inner peripheral wall (14) of the hollow section.
圆管状间隙（S1）在放置在中空段内的管状电极与中空段的内周壁（14）之间形成，电镀液在该 间隙（S1）中流动。
Simulation and experiment show: the balanceable inter-electrode gap linearly increases with the increase of the voltage, nonlinearly decreases with the increase of the feeding velocity;
模拟和实验表明：极限平衡间隙随极间电压升高而升高，它们呈近似的线性关系；随阴极进给速度增加，极间平衡间隙非线性地降低；
Simulation and experiment show: the balanceable inter-electrode gap linearly increases with the increase of the voltage, nonlinearly decreases with the increase of the feeding velocity;
模拟和实验表明：极限平衡间隙随极间电压升高而升高，它们呈近似的线性关系；随阴极进给速度增加，极间平衡间隙非线性地降低；
应用推荐