With the increase of displacement speed, fracture mode of the river patterns gradually became obvious and fracture surface became coarser.
随着加载速度的加快，河流纹断裂形态逐渐变得明显，同时断口形貌变得更加粗糙。
The fracture stress of DP microstructure increased with the increase of displacement speed, and the microcrack density increased with the decrease of displacement speed.
双态组织的断裂应力随加载速度的上升而增加，微裂纹面密度随加载速度的增加明显下降；
The results indicate that the difference of fracture toughness between MD and CD increases with a decrease in jet_wire speed ratio, and the main reason is stronger fibre orientation.
试验结果表明：减小浆网速比，增强了纤维定向作用，裂缝纵向分布增加，导致纸张中纵横向断裂韧性差异增加。
In this paper, tbe reasons for the fracture of an infinitely variable speed twist shaft which is used in spining wheel are analyzed.
对纺织机械用无级变速扭轴断裂原因进行了失效分析。
The speed of flowback during fracturing influences the damage of liquid invading when taking a fracture measure to a low permeability condensate reservoir.
在对低渗透凝析气藏采取压裂措施时，压裂后的返排过程影响到液锁对地层的伤害程度。
Loading speed is a key factor affecting the fracture splitting quality, and proper loading speed can increase the brittleness of material.
加载速率是影响裂解质量的重要因素，合理的加载速率可以提高材料的脆性。
If the capsule's quality can't meet the demand, the excessive rapid release speed of the breaker would lead to the fracture fluid viscosity premature descending and inducing the failure of work.
但是如果制作胶囊破胶剂的囊壳材料不好，胶囊破胶剂释放速率过快则会使压裂液提前破胶，导致施工失败。
On the basis of finding out the reasons for colloidal silica fracture, the bed layer flow speed was decreased through increasing 18.3% of the adsorption column diameter to lead-out a part of tail gas.
在找出硅胶破碎原因的基础上，通过吸附塔直径放大18.3%，引出部分尾气，使床层流速降低。
Through microscopic analysis of brass during high speed deformation, the deformation and fracture mechanism of brass under dynamic load are discussed.
通过对高速变形的黄铜进行细观分析，探讨了动载下黄铜的变形和破坏机理；
The retardation of tensile overload will reduce the 321SS crack growth speed for the furcation on the fracture section.
拉伸超载能阻滞321不锈钢的疲劳裂纹扩展速率，样品断面有明显的周期性的裂纹偏折或分叉；
The dynamic impact energies of 16MnR welded joints were determined with high speed impact test, and the influencing factors and fracture morphology were studied.
这些工作主要讨论了金属泡沫材料的拉伸、压缩、能量吸收、动态冲击、失效准则、本构关系、蠕变、疲劳和断裂等力学性能 。
The dynamic impact energies of 16MnR welded joints were determined with high speed impact test, and the influencing factors and fracture morphology were studied.
这些工作主要讨论了金属泡沫材料的拉伸、压缩、能量吸收、动态冲击、失效准则、本构关系、蠕变、疲劳和断裂等力学性能 。
应用推荐