The results show that the fracture mode is fatigue.
结果表明：钛合金壳体的裂纹性质为疲劳开裂；
The fracture mode is ductile and brittle mixed fracture.
其断裂形式为韧性和脆性的混合型断裂。
The results indicated that the fracture mode is the fatigue failure.
结果表明，其断裂形式为弯曲疲劳断裂。
The results indicated that the fracture mode is the fatigue failure.
断口实验结果表明，接头断裂模式为解理断裂。
The results show that the fracture mode of the pins is fatigue fracture.
结果表明：高压电容引脚断裂性质为疲劳断裂。
The influence of fracture mode and wear surface pullout on wear resistance was studied.
研究了断裂方式对磨损表面剥落和耐磨性的影响。
The possibilities of the fracture mode type C were higher as the bonding strength increased.
C型断裂模式随着剪切强度增加出现概率也增加。
SEM results demonstrated that the main fracture mode of the material is the split between filler and matrix.
结合SEM观察结果，判定该材料的断裂模式以颗粒与基材的界面分离为主。
The fracture mode of dry samples is all brittle fracture; Wet samples are not fracture only at high temperature.
干态试样的断裂形式都为脆性断裂，湿态试样只有在高温下未发生断裂。
The fatigue fracture mode of LY12CZ aluminum alloy specimen with coating is investigated under stress control condition.
在应力控制下，分析带有涂层的LY 12CZ铝合金构件疲劳断裂方式。
This paper proposes the analytical method for fracture mode and design method for prevention of brittle fracture at low temperature.
提出了钢结构断裂模式的分析方法和钢结构低温脆断设计方法。
The S-N curves for internal fracture mode are not affected by surface conditions, which is an inherent characteristic of the material.
内部破坏模式的S - N曲线不受表面条件的影响，是材料固有的特性。
With the increase of displacement speed, fracture mode of the river patterns gradually became obvious and fracture surface became coarser.
随着加载速度的加快，河流纹断裂形态逐渐变得明显，同时断口形貌变得更加粗糙。
The tensile and fatigue fracture mode is also different in different aging conditions, which is affected by the slip behavior of the alloy.
在不同时效状态，合金的拉伸和疲劳断裂方式亦不同，拉伸和疲劳断裂方式受合金形变行为的影响。
The effect of dynamic shear and tensile strength of tungsten heavy alloys on the fracture mode of fragmentation under explosive loading was investigated.
研究钨合金动态抗拉和抗剪强度对爆炸加载下破片宏观断裂模式的影响。
Through the analysis of test results and stress fields, the change of metal materials' ductile fracture mode with different stress condition parameters are discussed.
通过试验结果与应力场分析，讨论了不同应力状态参数下，金属材料韧性断裂形式的变化规律。
The fracture mode and cause were analyzed and determined by fracture surface observation, metallurgical structure examination, chemical analysis and hardness testing.
通过断口宏微观观察、金相组织检查、化学成分及硬度检测等手段确定了叶片断裂性质和原因。
The brittle morphologies become much more notable, and appear the inter-and trans-granular fracture mode after sodium corrosion at high temperature for both of W-specimens.
钠腐蚀后，两种钨试样的沿晶脆断特征变得更为显著，为沿晶和穿晶混合型脆性断裂。
The result shows that the fracture mode is low stress brittle fracture. The fracture is mainly caused by needle type martensite in the heat affected zone of the weld joint.
结果表明，在连接杆焊缝附近的热影响区中存在大量针状马氏体组织，在低应力的作用下，导致材料发生脆性断裂。
The results show that the fracture mode of blade is vibration fatigue and the main cause of initiation of fatigue crack is the mismatch between rabbet and tongue-and-groove.
结果表明，叶片的断裂模式为振动疲劳，叶片榫头与榫槽配合不当是萌生疲劳裂纹的主要原因。
According to the fracture surfaces, it is found that the fracture mode of the two parts is overload fracture and there is obvious stress concentration in the floating piston.
但从现有的断口看，二者均呈大应力过载断裂且浮动活塞明显受力不均。
It was revealed that local strain rate is a key factor that builds a bridge between different tests, different samples and different cracking processes, and dominates fracture mode.
结果表明，在该体系中局部应变速率是联系各种不同断裂过程的纽带，决定着断裂的模式。
It is shown that the zigzag grain boundary may delay the initiation, growth and propagation of crack, as well as may also influence the crack morphology and the fracture mode markedly.
研究表明，弯曲晶界对裂纹的萌生、长大及扩展，对裂纹的形态及断裂方式，都有显著的影响。
The failure parts of the CVT metal V-belt which produced in domestic ruptures are analyzed, the break source position is found and the fracture mode of the failure blocks is presented.
通过对某型国产CVT金属带断裂件进行失效分析，发现了摩擦片断裂源位置，提出了摩擦片的失效模式。
By means of stereomicroscopy and scanning electronic microscopy (SEM), the fracture mode and mechanism of the broken K18 superalloy cast blade in a supercharger turbo were investigated.
采用体视显微镜、扫描电镜等分析手段对K18合金增压器涡轮铸造叶片的断裂形貌与断裂机制等进行了分析。
One is called the S-N curve of surface fracture mode. It is governed by a crystal slip on the specimen surface, which occurs in the region of short fatigue life and high stress amplitude level.
一组叫做表面破坏模式的S-N曲线，它发生在高应力幅短寿命区，是由试样表面晶体滑移引起的。
One is called the S-N curve of surface fracture mode. It is governed by a crystal slip on the specimen surface, which occurs in the region of short fatigue life and high stress amplitude level.
一组叫做表面破坏模式的S-N曲线，它发生在高应力幅短寿命区，是由试样表面晶体滑移引起的。
应用推荐