The maximum efficiency of 91% is obtained in this forward converter.
设计的正激变换器的最高效率达到91%。
Only with the magnetic reset circuit, can the forward converter work.
采用正激变换器必须要有磁复位电路才能正常工作。
Active clamp forward converter has many advantages and is widely used.
有源箝位正激变换器有很多优点，现在正得到广泛应用。
A novel push pull forward converter is proposed and its principle is analyzed.
介绍了一种新颖的正激推挽变换器。
The analysis and design of an active clamped forward converter is presented in this paper.
二本文论述了有源钳位正激变换器的原理与设计。
The first stage is push pull forward converter, and the second stage is a dual buck inverter(DBI).
该静止变流器前级采用推挽正激式变换器，后级采用双降压式逆变器。
The principle and design of a zero voltage transition PWM forward converter are presented in this paper.
论述了零电压过渡PWM正激变换器的原理与设计。
The basic circuit configuration and operation principle of dual switch forward converter based on SG3525 are introduced.
主要介绍了由SG3525构成的双管正激型开关稳压电源的基本电路结构和工作原理。
The active clamp ZVS-PWM forward converter has been answered for with the merits of the soft switch technique and the magnetic reset technique.
有源钳位z VS - PW M正激变换器可以适应这一发展趋势，因为它具有软开关和磁芯自动复位功能。
Performance of RCD reset asymmetrical dual-switch forward converter is the lowest, the configuration is the simplest and the cost is the lowest.
RCD复位不对称双管正激变换器性能相对最差，结构最简单，成本最低。
It is clear that the traditional single-ended forward converter is difficult to adapt to the trend, so, it is necessary to find a novel topology.
很显然，传统的单端正激变换器很难适应这一发展趋势，因此，必须找到一种新型的拓扑结构。
This circuit has the character of the flyback converter as well as the forward converter, single voltage output can be achieved by one transformer.
这种变换器综合了正激和反激变换器的特点，并且只用一个变压器实现了单路电压输出。
The traditional interleaved two transistor forward converter exists high voltage stress of freewheeling diode when applied in high output voltage condition.
传统交错并联双管正激组合变换器应用于高电压输出场合时存在变换器次级电压偏高、高频整流二极管电压应力大的问题。
The operating principle of RCD clamped forward converter is carefully analyzed. The design trade offs and procedures of the RCD clamped network are provided.
本文详细分析了RCD箝位正激变换器的工作原理，给出了RCD箝位网络的设计准则和步骤。
In this paper, a design method and the operating principles of pulse transformer in forward converter are presented, and some problems to be considered are pointed.
该文介绍了单端正激式脉冲变压器的工作原理和设计方法，指出了在设计时应注意的问题。
Results show that performance of active-clamped asymmetrical dual-switch forward converter is the highest, the configuration is the most complex and the cost is the highest.
结果表明，有源箝位不对称双管正激变换器性能最佳，结构最复杂，成本最高。
One inherent limitation of the forward converter is that the transformer must be reset during the power transistor off period. Thus, additional reset circuitry has to be used.
但是它的一个固有缺陷是功率晶体管截止期间变压器必须磁复位，因而需要采用附加的复位电路。
Novel control for an input-series and output - parallel dual two-transistor forward converter (ISOP-DTTFC) is proposed, based on the analysis and result on the voltage unbalance.
分析了交错控制输入串联输出并联组合式双管正激变换器输入端不均压现象及其起因。
The model setting up method of the three module which include power factor correction circuit, two-transistor forward converter, secondly chopper circuit, is discussed in detail.
分别讨论了功率因数校正模块、双正激变换电路模块和二次斩波模块的建模方法。
This paper introduces the circuit topology of portable inverter arc welder with soft snubber, mainly power circuit is a double switch forward converter with assistant resonant circuit.
主电路采用具有无源辅助谐振网络的双管正激变换器，与普通双管正激变换器相比，功率管开关状态得到较好的改善，同时并没有增加电路的复杂性。
But, despite its merits, the traditional single-ended forward converter has some shortcomings, such as simple circuit, low parts count, low output ripple, etc, it also has some shortcomings.
尽管传统的单端正激变换器有诸多优点，如电路结构简单、元件数量少、输出纹波小等，但是也有其缺点。
A new sort switch topology of two-switch forward converter and xenon-lamp simmer circuit was designed, the principle of their main circuit was analyzed and some key parameters were calculated.
设计了一种双正激电路的软开关和预燃电路，分析了它们的工作原理，推导了一些关键技术参数的计算公式。
Application of a new lossless clamp circuit for single ended forward converter is introduced, the operation principle of this circuit is analyzed in detail, and the experiment result is also given.
介绍了一种新型无损箝位电路在单端正激电源中的应用，详细分析了工作原理，并给出了实验结果。
Some measures to security use converter gas were put forward.
并介绍了安全使用转炉煤气应采取的措施。
The control strategy of the parallel converter of the UPFC is put forward in term of its function.
根据并联变流器在UPFC的作用提出并联变流器的相应控制策略。
Without the need of any auxiliary switches or complex passive resonant network, the converter can achieve ZVS in both forward and backward modes.
不需要任何辅助开关或无源谐振网络，变换器就可在双向变换工作中实现零电压开关。
The causes of bottom blowing failure for combined blowing converter were analyzed and the preventive measures were put forward.
分析顶底复吹转炉底吹失效的原因并提出预防措施。
By discussing about sampling method of liquid steel in converter, this article puts forward new sampling methods.
通过对转炉冶炼钢的熔炼成分取样方法的探讨，提出新的取样方法。
This paper proposes a symmetrical RCD clamp dual switch forward-flyback with current-doubler-rectifier (CDR) converter which adopts the staggered clamp structure with two RCD type circuit.
该文提出一种对称式RCD箝位的倍流整流双管正-反激型直流变换器。
This paper proposes a symmetrical RCD clamp dual switch forward-flyback with current-doubler-rectifier (CDR) converter which adopts the staggered clamp structure with two RCD type circuit.
该文提出一种对称式RCD箝位的倍流整流双管正-反激型直流变换器。
应用推荐