Establish the force model formula of drilling cuttings.
建立了钻屑颗粒的受力模型表达式。
At last, the cutting force model is validated through cutting tests.
最后，通过切削实验对切削力模型进行了验证。
Rolling force model is the crucial model for process control in cold rolling.
轧制力数学模型是冷轧工艺控制系统的中枢模型。
Our constantly changing curvature based internal force model is scale invariant.
据此，提出了基于恒定曲率变化的内部力模型。
According to the experimental results, the force model of PDC cutter breaking rock was developed.
根据试验结果，建立了PD C切削齿破岩的受力模型。
On the basis of theoretic analysis and experiment, the new rolling force model has been developed.
通过理论推导和现场实验相结合，建立了新的轧制力模型。
An orthogonal cutting force model with tool flank wear has been analyzed based on cutting test investigation.
在试验研究基础上进行了有后刀面磨损的正交切削模型分析。
The damping force model of the damper and the nonlinear mathematical model of vibration reduction system are established.
建立了新型磁流体阻尼器的阻尼力模型及其减振系统的非线性数学模型。
This is very helpful to choose suitable nonlinear oil film force model in the dynamic analysis for rotor-bearing systems.
这为进行转子-轴承系统的非线性动力学分析时选取恰当的油膜力模型提供了理论指导。
A simple milling force model for end-milling cutter is improved. The dynamic milling force and moment models are proposed.
将一种简易的端铣刀铣削力模型改进为动态铣削力模型，并给出了铣削力矩模型。
The result of on-line application indicated that rolling force model has good precision of prediction with an error less than 5%.
现场在线应用结果表明：给出的轧制力模型具有良好的预测精度，预测误差可以控制在5%以内。
Strokes sequence based rendering architecture, corresponding collision detection and virtual force model were briefly introduced.
首先简介了基于有序笔画的汉字力觉渲染架构、快速碰撞检测算法和虚拟力模型。
The parameters in the restoring force model corresponding to the design parameters of SRC member and structure are also determined.
建立了型钢砼结构（空腹式）的光滑恢复力模型参数与结构设计参数的关系；
The calculation equations of distributed force model are derived for actuators bonded on structure by single-sided and double-sided.
分别导出了单面粘贴驱动器和双面粘贴驱动器时的分布力模型的计算公式。
Then, the damage index recording the material's behavior is integrated into restoring force model of reinforcement and concrete respectively.
将这一记录材料性能信息的损伤指标带入材料各自的恢复力模型以考虑产生损伤后材料的强度和刚度退化。
Consulting the previous research, the paper suggested the calculation method of every characteristic parameter point in restoring force model.
参考前期研究成果提出了恢复力模型中各个特征参数点的计算方法。
Based on the tests and theoretic derivation, skeleton curve of restoring force model of frame column with high axial compression ratio is got.
在试验研究和理论推导的基础上，给出了高轴压比下框架柱恢复力模型的骨架曲线，与试验骨架曲线吻合较好。
Based on traditional cutting force model in face milling, a new cutting force model for the prediction of static cutting forces has been presented.
以传统的端铣切削力模型为基础，提出了一种新的端铣加工中静态切削力的预报模型。
The distributed force model of intelligent beam structures is presented considering the effect of bonding layer on the basis of theory of linear strain.
以线性应变理论为基础，提出了考虑粘贴层影响的智能结构梁分布力模型。
The traditional rolling force model of 4-stand tandem cold strip mill at Anshan Iron and Steel Corporation was analyzed, and some defects were found out.
分析了鞍钢冷轧厂4机架冷连轧机轧制力模型，指出了其存在的主要缺陷，并提出了改进方案。
The conventional inter-particle force model, including van der Waals force, Coulomb force and image force, could not explain these interaction behaviors.
受力分析表明，包含范德华力、静电库仑力和电像力的传统颗粒间作用力模型不能解释这种相互作用行为。
In this method, an inter floor shear model is adopted for the whole RC structure; and a quadrilinear recovery force model, for the RC inter floor columns.
该方法中钢筋混凝土框架整体结构采用层间剪切模型，柱采用四线性恢复力模型。
It is found that within the limits of error our conclusion on electric field distribution is consistent with that of the inertial centrifugal force model.
在误差允许的范围内，本模型有关电场强度分布的结论与惯性离心模型一致。
The restoring force model and the method for dealing with the characteristic value are also given, which can be applied to the elastoplastic dynamic analysis.
还给出恢复力模型及其特征点的取值方法，可进行底部框架抗震墙砖房的弹塑性动力分析。
The good thing was once these decisions were made, I was able to quickly brute force model and get things where I needed them to start setting up the rendering.
好在这些方案用在设计中后，我就会很快地搞定模型，得到我所需要的东西，接下来开始我的渲染。
The spatial force model of the drive is presented. Forces between planet and worm or stator are analyzed. The formula of the output torque for the drive is given.
研究了机电集成超环面传动的驱动机理，建立了该传动的空间力学模型，分析了行星轮在环面蜗杆和环面定子处的受力情况，推导出了行星架输出力矩的计算公式。
Based on the test results and analysis, restoring force model of composite steel concrete beam was established with consideration of the degree of shear connection.
在试验研究的基础上，考虑了剪力连接程度的影响，建立了钢—混凝土组合梁的恢复力模型，并编制了相应的计算程序。
On the basis of cutting force model and vibration model of machine tools structure, the effect of the regenerative chatter on the stability of end milling is focused.
存得到切削力模型和机床结构振动模型的基础上，着重研究了再生型颤振对铣削加工过程稳定性的影响。
Based on the rigid plastic constitutive equation of lead, the damping force model of lead extrusion damper was deduced from the even plastic deformation energy method.
本文根据铅的刚塑性本构关系，利用均匀塑性变形能法，推导了铅挤压阻尼器的阻尼力滞回模型。
The distributed force model of intelligent beam structures is presented in considering the effect of bonding layer on basis of hypothesis of linear strain in the paper.
基于线性应变假设，提出了考虑粘贴层影响的智能结构梁分布力模型。
应用推荐