Honing load includes mass load and force load.
珩磨负载包括质量负载和力负载。
In fact, it is somewhat desirable to use lower powered hardware in system test in order to force load related bug discovery earlier.
事实上，为了更早地发现与加载有关的错误，在系统中使用功能更低的硬件是比较合适的。
AIM: to investigate the effects of torque force load on the stress distribution in implant bone interface, so as to help the clinical selection of implant location.
目的：研究扭转力载荷对支抗种植体骨界面应力分布的影响，以指导临床正确选择支抗种植体的植入部位。
At the start of an ALLOW NO ACCESS load operation, the utility may force concurrent applications that are trying to read from or write to the target table.
在ALLOWNOACCESS加载操作的开始，该工具可能会压制那些试图读或写目标表的并发应用程序。
Note: If you don't see it, the plug-in is not dynamically loaded, so you need to use the -clean parameter to restart Rational Software Architect, which will force it to load the new plug-in.
注意：如果您没有看到，那么插件没有被动态地加载上，因此，您需要使用- clean参数重新启动Rational Software Architect，这样将使它加载新的插件。
Pump is the drainage and back into the groove of reasonable design, is a gear in the work under the minimum torque force, so the bearing load is small, wear small, pump with high efficiency.
输送皂角泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
RADIAL FORCE : The load on a bearing perpendicular to the axle, this and the Thrust load are forces that affect the design and application of bearings.
径向力：与轴承的轴线所垂直的载荷；它和轴向力是影响轴承设计和应用的两个力。
"The skeleton is a smart structural organ and knows how much load [force] is being put on it," Recker says.
“骨骼是一种智能结构的器官，知道自己承受了多少负荷(力)，”莱克尔说。
Once the form is submitted via the driver.click (" submit ") call, I force Selenium to wait for the response to load and then I assert the presence of a successful creation message.
通过调用driver. click (“submit ”)提交表单后，Selenium将等待响应的加载，然后我将断言成功的创建信息。
It is known that in plane finite element calculation the bearing load must be transformed into force of nodal.
在平面有限元计算中，必须把轴承负荷转为节点力。
Distributive regularities of inner force of pile under static and dynamic load, the change of pile's side resistance, and settlement of piles are analyzed by static and dynamic load test.
通过单桩竖向抗压静载试验和动载试验，分析了静动载对桩身轴力分布、桩身侧摩阻力和基桩沉降的影响及其变化规律。
A particularly attractive feature of the hydraulic load cell is that force calibration is not required.
一个特别有吸引力的特点，液压负荷单元是力的标定是不是必需的。
The force needed at one end of the lever to move the load at the other end of the lever depends on the distances to the pivot.
杠杆的一端所需要的、去移动另一端的东西的力，取决于与支点的距离。
For vacuum circuit breaker with spring operating mechanism, an optimum design of CAM mechanism is significant to make the output force characteristics match the load characteristics.
对与真空断路器相配的弹簧操动机构而言，其输出力特性和开关负载特性的合理匹配取决于凸轮机构的合理设计。
On this basis, back electromotive force without load and with load is researched, simulated and analyzed, and cogging torque is analyzed and calculated in different dimensions of magnetic steel.
在此基础上，仿真了空载和负载下的电机反电动势，并且对不同磁钢尺寸下的定位力矩进行了分析计算。
Rocket engine test stand exerts force on a load cell.
火箭发动机试验的立场，施加武力对负载细胞。
Aimed at a straddle blade root, the influence of the interface friction coefficient and initial clearance on the contact force distribution, load distribution and the maximum stress is analyzed.
文中以一菌型叶根为对象，分析了界面摩擦系数和初始间隙对接触力分布、载荷分配及最大应力的影响。
The article have expounded the load acting on PC single track beam, and the calculation of curved PC single track beam including force, prestress and the stress etc.
阐述了作用于PC轨道梁桥结构上的荷载，曲线pc轨道梁的内力计算，预应力计算，应力计算及组合。
In the load calculator part, the paper lucubrates the calculation of wind force considering the spatial effect.
在荷载计算部分，较为深入的研究了考虑空间效应的风荷载的计算方法。
The precise formula of node force fitted second order distributed load is developed sing virtual work principle.
使用虚功原理和位移线性插值推导了满足二次分布力作用的精确节点力分配公式。
In the Bohai sea, especially in the Liaodong Bay, sea ice force is the controlling load in Marine engineering design.
在渤海，特别是在辽东湾，海冰作用力是海洋工程设计的控制荷载。
The bearing chain bears the equilibrium load to reduce the force on the main drive chain to a great degree.
承载链直接承受平衡载荷，可大幅度减小主传动链的受力。
The internal force produced in live load is calculated by manual loading method.
活载产生的内力采用手工加载的方法计算。
Internal force of curve beam under uniform load is analyzed in this paper, and simplified method of computing moment is given.
本文分析并推求了均布荷载下平面弧形梁的弯矩、扭矩计算公式，并提出弯矩的简化计算方法。
According to the measured results, it discussed the affection of resisting force of mine, lifting load and the mass changing of steel-wire rope.
根据实测结果，讨论了矿井阻力、提升载荷及提升钢丝绳重量变化对实测的影响。
On this basis, force or displacement load is exerted to find a reasonable adjusting method, in the way the surface figure requirement can be met.
在此基础上，通过施加力或位移进行多点调节，找到合理的调节方法，使面形精度达到要求。
On this basis, force or displacement load is exerted to find a reasonable adjusting method, in the way the surface figure requirement can be met.
在此基础上，通过施加力或位移进行多点调节，找到合理的调节方法，使面形精度达到要求。
应用推荐