Optical aligned check for shaft system after boring.
轴系镗孔后光学校中检查。
Load test for shaft generator and function test on sea trial.
轴带发电机负荷测验和航行时效用测验。
Load test for shaft generator and its function test on sea trial.
轴带发电机负荷试验和航行时效用试验。
Supplies reasonable design with theory basis for shaft impact crusher.
为立式冲击破碎机的合理设计提供了理论依据。
American 1500en graphite packing is chosen as sealing material for shaft end.
改进密封结构，增加传动轴外置密封体，选用美国1500EN石墨盘根为轴头密封填充材料。
This paper discusses design ideas and achievement of CAPP system for shaft parts.
论述了轴类零件CAPP系统的设计思想、实现方法。
Inspecting centerline positioning for shaft system and rudder system before boring.
轴、舵系镗孔前中心线定位检查。
Load test for shaft generator and its function test on sea trial. Interlocking reliability test.
轴带发电机负荷试验和航行时效用试验。
The automatic control system for shaft furnace roasting in Jiu Steel's Concentrator is described.
介绍了酒钢选矿厂竖炉焙烧自动控制系统。
This paper presents experimental results for shaft seal assembly with three kinds of different support seats.
本文介绍了三组不同支座的轴密封部件试验结果。
In the fourth chapter, the method of assembly feasibility analysis for shaft and hole feature was established.
第四章：建立轴孔要素装配可行性分析方法。
Mainly utilized in the cold, hot cutting process for shaft products, as well as in the construction engineering structure.
主要用于轴类的冷、热切削加工，同时也用于建筑工程结构中。
The author introduces the primary design of distributed computer controlling system for shaft kiln in Huangshi cement plant.
本文对黄石市水泥厂立窑分布式计算机控制系统初步设计作了介绍。
Incremental motion encoder (IME) is a new type of transducer for shaft center trace measurement with resolution up to sub-micro.
运动增量编码器(IME)是一种新型的轴心轨迹测量传感器，其测量灵敏度可以达到亚微米级。
Based on some shaft projects for tunnel, different construction methods for shaft, in different geological conditions are discussed.
结合几个实际工程，探讨了不同地质条件下隧道竖井采用的不同施工方法。
It is more necessary to study the mechanical properties in order to provide reasonable design parameters for shaft frozen sidewalls.
为了给立井冻结壁和井壁设计提供合理的设计参数，对冻结壁岩石的力学特性试验很有必要。
Requirements on agitator drives; agitator speed and direction, bearing application running accuracy, dismounting space for shaft seal.
搅拌器传动装置的要求。旋转速度和旋转方向，轴承应用。
The calculation made a design for shaft wall structure under vertical addition force should consider the problem of space axially symmetry.
在考虑竖向附加力作用时，井壁结构的设计计算应按空间轴对称问题考虑。
The problems of deformation for shaft lining are investigated under arbitrary axisymmetric normal loads and tangential loads with end loads.
对有限长立井井壁在任意轴对称的法向、切向以及端面荷载的共同作用下的变形问题作了分析研究。
It provides the experiential and technical assistance for shaft sinking by freezing method in thick overburden of Juye coalfield and other mining areas.
本文总结了龙固副井的冻结施工工艺，为巨野煤田以及深厚表土的冻结施工提供了经验和技术保证。
The seal structure is improved and external seal for drive shaft is added. American 1500en graphite packing is chosen as sealing material for shaft end.
改进密封结构，增加传动轴外置密封体，选用美国1500en石墨盘根为轴头密封填充材料。
A method for shaft part size detection based on digital synchronous technique is proposed according to the characteristics of scanning 2-d image with linear CCD.
根据线阵CCD对二维图像进行扫描检测的特点，提出一种基于数字同步技术的轴类零件尺寸检测方法。
The best set of mechanise is put out, named as "922111", with the present equipment for shaft construction. The mixing work style of cutting and building in short section.
在我国现有先进凿井设备条件下，选择短段掘砌混合作业方式，提出了深立井机械化配套的最佳模式是以“922111”为内容的综合机械化作业线。
Single row angular contact ball bearings in tandem arrangement must always be adjusted against another bearing inversely arranged for shaft guidance in the opposite direction.
单列角接触球轴承串联布置必须始终另一个轴承对轴的指导成反比安排在相反的方向调整。
Through the status analysis on shaft seal system of 9E combined-cycle steam turbine, the improvement for shaft seal overflow is put forward to save energy and reduce consumption.
通过对9E联合循环汽轮机轴封系统的现状分析，提出对轴封溢流的改造以达到节能降耗的目的。
This system that can be operated on a micro-computer is based on group technology and uses the semi-generative principle to carry put the technology process design for shaft parts.
本系统以成组技术为基础，采用半创成式生成原理进行轴类零件的工艺过程设计。
The special machine tools for shaft parts' research and design is in the field of "reconstruction of machine technique" . This topic came from the project of XinWei oil nozzle & oil pump Cop.
本论文课题《轴类零件专用机床的研究与设计》来源于江苏南通星维油嘴油泵厂的实际工程项目。
Classical testing methods for shaft steelworks have been introduced in this paper. The principles, the causes of error, the accuracy for measurement and the cost-efficiency are compared in detail.
总结了刚性罐道性能检测的常用方法，从原理、误差来源、测试精度和经济性等几方面作了详细比较。
For example, by using multiple motors on the same shaft it is possible to get more than one degree of freedom.
例如，通过在同一传动轴上使用多台电机，可能使该机构获得一个以上的自由度。
For example, by using multiple motors on the same shaft it is possible to get more than one degree of freedom.
例如，通过在同一传动轴上使用多台电机，可能使该机构获得一个以上的自由度。
应用推荐