The flow chart in Figure 1 demonstrates how TAMOS implements the security layer by intercepting the system calls at the kernel level.
图1的流程图演示了TAMOS如何通过在内核层面拦截系统调用来实现安全层。
Finally, the system flow chart diagram and procedures.
最后给出了系统框图和程序流程图。
This paper introduces a handwritten digit recognition system based on TMS320VC5402. The work principle is presented and the block diagram of hardware and program flow chart are given .
介绍了基于TMS320VC5402的手写数字识别系统和该系统的基本原理，给出了它的硬件原理图和软件设计程序框图。
It describes the system structure, a part of system flow chart. It provides some measures for improving produce safety.
介绍了系统构成和工艺流程，给出了部分系统流程图及提高安全生产的各项措施。
It gives system Program Flow Chart and Data Flow Diagram and Structured Design Diagram and UML modeling Diagram.
并给出了系统的流程图、数据流图、系统设计的结构图和UML图。
Base on the main problem of vacuum ejector waste system, this paper set out overhaul flow chart and raise check and overhaul method.
根据污物收集系统的常见故障，列出了检修流程图，提出了检查方法和检修要点。
The fourth chapter system design, this paper introduces the overall function, database system, the design of the flow chart and UI.
第四章系统的设计，介绍了系统的总体功能、数据库、UI以及各流程图的设计。
This paper detailedly introduces the whole design scheme of the system, the circuit on interface module and 89c51, the method of the software design and program flow chart.
详细阐述了系统的总体设计方案，给出了界面模块与89c51接口电路，最后介绍了软件设计方法及程序流程图。
Software has partially produced the system key partial procedures source code and the flow chart.
软件部分给出了系统关键部分的程序源码和流程图。
Select the valve size combinations from SIZING CHART that is within low to high flow system range.
在最低到最高流量范围内，从通径图表中选择阀门通径。
System structure chart, hardware circuit and software flow chart were given.
给出了系统结构图、报警节点电气连接图和软件流程。
Comparisons are made among the flow control system and temperature control system as well as viscosity control system, and the flow block chart of flow control system is given.
对流量控制系统与温度控制系统及粘度控制系统进行了比较，给出了流量控制系统的流程框图。
The work flow of system and the flow chart of each TCP/IP module are given out, too.
文中给出了系统的工作流程以及TCP／IP各个了模块实现的流程图。
The article not only presents system flow chart in process, but also lists software flow chart.
文章不仅给出了开发过程的系统流程图，还列出了软件开发的流程图。
In this article has also attached the function flow chart, reads this article to be possible carefully to have the quite detailed understanding to this system operation.
本文中还附了功能流程图，仔细阅读本文可对本系统的操作有比较详细的了解。
On the basis of describing the theory of measuring the resistance, gives the flow chart of the system hardware as well as describes the key technology about every part in particularly.
在阐述视电阻率检测原理基础上，给出了系统硬件基本框图，详细叙述了各部分采用的关键技术及原理。
The function flow chart of this digital servo system is given, too.
并且给出了其数字伺服系统功能流程图。
System chart and program flow chart are presented.
给出了系统的结构框图及程序流程图。
The system design framework and software design flow chart are described in detail.
从硬件和软件两方面详细阐述了系统的设计框架和软件设计流程。
The overall sketch of the decision support system, function description and logic flow chart are given.
本文全面论述了这一决策支持系统的组成、功能和关键技术。
And introduced its software and hardware design methods and the system is the principle of hardware, software flow chart.
并介绍了其软、硬件设计的方法和给出了系统的硬件原理图、软件流程图。
The design of the first ball on the size of the work of classification diagram and work flow chart of the control system.
本设计首先介绍了大小球分类的工作示意图和工作流程图，分析了控制系统的要求。
The next chapter in the function and flow chart of the system was introduced.
接下来的一章里对系统功能与流程图进行了介绍。
This paper analyzes the principle, working flow chart and anti-jamming measurement of the electrocardiogram signal collection and memory system.
对心电图信号采集与存储系统的工作原理、工作流程以及抗干扰等问题进行了分析。
Ensemble sys-tem reliability design flow chart, system reliability model and formulae are given. And a weighting coefficient is introduced to the computing by means of practical situation.
文中给出了可靠性总体设计流程图、系统可靠性模型和计算公式，并在计算中根据实际情况引进了加权系数。
This paper is mainly concerned about the system analysis, design and implementation process of automobile marketing prediction system in FAW. Plain flow chart of system architecture is also shown.
本文详细阐述了一汽汽车销售预测系统的系统分析、系统设计与系统实施过程，并给出了清晰的系统结构流程图。
Finally, the flow chart of the system, design of numerical simulation module, and program interface are explained and the resolutions of key parts of simulation design are given.
最后对整个软件设计流程、数值仿真模块的程序设计以及与动力学分析主模块的接口作了说明，并对仿真的关键部分与重点给出了解决方法。
It also provides system diagram, key circuitry and software flow chart.
给出了系统框图、关键电路图以及软件流程。
The hardware design and software flow chart of the parameter test system were give out.
具体给出了参数检测系统的硬件设计及软件控制流程。
The hardware design and software flow chart of the parameter test system were give out.
具体给出了参数检测系统的硬件设计及软件控制流程。
应用推荐