This article introduces the technique of flat welding.
并介绍在横位置的横焊技术。
Flat welding flange of the major design drawback is that it can not guarantee no leakage.
焊法兰的主要设计缺点是它不能保证无泄漏。
Flat welding flange not only saves space, reduces weight, more importantly, to ensure that joints do not leak, has good sealing performance.
平焊法兰不仅节省了空间、减轻了重量，更重要的是确保接头部位不会发生泄漏，具有良好的密封性能。
Application of stainless steel after welding (not by steel) flat shovel thoroughly clean slag and spatter.
焊后应用不锈钢(不得采用碳钢)扁铲彻底清理熔渣和飞溅。
Welding principle and its operating process of flat copper wire in large transformer windings are introduced.
介绍了大型变压器绕组用扁铜导线的焊接原理及其操作工艺。
In the same time, a calculating formula of welding flat cover special for hydraulic test is deduced by setting certain safety coefficient of hydraulic test.
同时通过对试验压力取一定安全系数，推导出液压试验专用焊接平盖的计算公式。
The re-bar end used for electroslag welding should be straight, flat and clean free of U-shaped, bruising, concave and convex, bending or distorted deformations.
电渣压力焊焊接使用的钢筋端头应平直、干净，不得有马蹄形、压扁、凸凹不平、弯曲扭曲等严重变形。
All welding shall be in the inside of this assembly so that the brake assembly side is clear and flat.
全部焊接，须在大会内的这一点，这样的刹车装配方是明确和持平。
Double reversed star shape, interphase reactor, flat wave output circuit, stable welding current.
双反星型，平衡电抗器及平波输出电路，焊接电流稳定。
Tables positioned on either side of the welding table support and allow the foam sheets to lie flat and slide.
表中的位置，两旁的焊接表支持，并让泡沫板，以平躺及幻灯片。
The effective thermal input of pulse flash process is large, it can help reduce the drop weight test fracture of flat spot, which is suitable for welding U75V rail.
脉动闪光工艺的有效热输入大，有利于降低落锤断口灰斑，适合焊接U75V钢轨。
Used for down hand welding and flat fillet welding on general low-carbon steel structures…
适用于船体结构低碳钢和其他相应等级的普通低碳钢的平焊、平角焊。
When lifting the flat boxes the board cracks at the remaining board Bridges and after welding the final piece does not bend at right angles.
当处理平的杂志箱时，我们遇到了两个问题。当抬起箱子时，纸板在余下相连处断裂，重新焊接后，最后一片的弯曲角度不正确。
NC machine is used to ensure that longitudinal and circular weldings are produced at a constant speed and the welding point is always in flat position.
数控主机用于保证箱底纵、环焊缝焊速恒定并使焊接点始终处于平焊位置。
Open flat plate welding residual stress is greater than the original residual stresses.
开平板的焊接剩余应力大于原平板的焊接剩余应力。
Open flat plate welding residual stress is greater than the original residual stresses.
开平板的焊接剩余应力大于原平板的焊接剩余应力。
应用推荐