In this, can use repair drive shaft and bushing method to recover its normal fit clearance.
遇此，可采用修主动轴或衬套的方法恢复其正常的配合间隙。
If the drive shaft wear mild, just press the old bush changed after standard size bushing, fit clearance can be restored to allow range.
若主动轴磨损轻微，只需压出旧衬套后换上标准尺寸的衬套，配合间隙便可恢复到允许范围。
This paper describes the structural design of a vertical shafting, analyses and calculates the wobble error and fit clearance in the developed ballistic camera.
本文介绍了在研制“弹道相机”时，一种新型竖轴系的结构设计、轴系晃动误差和配合间隙的分析计算。
Researches on the influence of bolt fit clearance upon shearing stiffness was presented, in accordance with the shearing stiffness dispersivity of bolted fastenings.
针对螺栓连接件剪切刚度分散性问题，对螺栓配合间隙影响剪切刚度的重要因素开展研究。
The fit clearance between spool and sleeve decreases because of the thermal expansion of the spool caused by temperature increment, so it is possible that spool is deadlocked in sleeve.
油温升高使阀心受热膨胀，阀套与阀心间的配合间隙减小， 阀心有可能被卡死在阀套里。
It is the minimum clearance space intended between mating parts and represents the condition of tightest permissible fit.
它是配合零件之间最小的预期间隙空间，代表着允许的最紧配合条件。
Thee tubes fit inside each other with just enough clearance and no play.
管内适合对方刚好够清关和没有发挥。
Cylindrical bore bearing is usually installed with heat, reduce the use of interference fit bearing clearance, or achieving the purpose of pretension.
圆柱孔轴承通常采用热装，利用过盈配合减小轴承游隙，或者达到预紧的目的。
When machining parts with bore as positioning reference, if clearance fit positioning is adopted, machining accuracy is certainly affected due to the existence of clearance.
在精加工以内孔为定位基准的零件时，所用芯轴类工装如果采用间隙配合定位，由于定位间隙的存在，必然影响零件的加工精度。
The vent system composed of vent groove, vent plug and clearance of ejector pin can fit the need of venting.
采用分型面排气槽、顶杆间隙排气与排气塞排气相结合的排气系统设计能够很好地满足模具排气需要。
The tubes fit inside each other with just enough clearance and no play.
管内适合对方刚好够清关和没有发挥。
A magnetic sleeve (6) is sheathed on the outside surface of the support tube and is in clearance fit with the support tube.
套在支承管外表面的磁性套筒(6)与支承管间隙配合。
There are even injection moulding machines dedicated to making preforms having a rectangular tiebar clearance to fit the needs of making preforms.
有瓶坯专用的注塑机采用长型的四柱空间迎合瓶坯模具的需要。
In the rotating ring components, a rotating ring 3, an auxiliary seal ring 2 and a transmission seat 1 are assembled together by clearance fit.
旋转环组件中旋转环3、辅助密封圈2和传动座1之间采用过盈配合装配在一起。
In the rotating ring components, a rotating ring 3, an auxiliary seal ring 2 and a transmission seat 1 are assembled together by clearance fit.
旋转环组件中旋转环3、辅助密封圈2和传动座1之间采用过盈配合装配在一起。
应用推荐