Based on completion of wall strength calculation, then do the finite element stress analysis.
在完成管壁强度计算的基础上，进行管壁有限元应力分析。
Based on the broken gear teeth in contact fatigue test, bending fatigue life curve was got by applying finite element stress analysis results, MSC.
本文以接触疲劳试验中疲劳断齿齿轮为依据，利用有限元应力分析结果以及试验得到的弯曲疲劳寿命曲线，应用msc。
The integrated finite element stress analysis for a bladed disk assembly has been carried out, using the cyclic symmetric model with contact surfaces.
本文用含接触面的循环对称计算模型进行轮盘-叶片组件的统一有限无应力分析。
The three dimensional finite element stress analyses of main girder with twin-box cross section used commonly in cable-stayed bridge have been carried out.
本文对斜拉桥双箱单室箱形主梁进行了空间有限元应力分析。
This article uses the ANSYS software and analysis design method to make a detailed finite element stress analysis of the head of valve body where placed the quarter rings.
利用ANSYS软件及其分析设计方法，对阀体中腔安装四合环的位置进行了有限元应力分析。
The satisfactory results are obtained by using concrete calculative examples, A new method is provided to carry out finite element stress analysis for different modulus material.
经过实例分析计算，获得了满意的结果。为对这类材料的结构进行有限元应力分析提供了一种新方法。
The finite element stress calculation of the hydraulic rocking shear stand has been described, and the optimization has been carried on in two aspects of force condition and configuration.
介绍液压摆式剪切机机架的有限元应力计算，从受力状态和结构两方面进行优化。
Methods: the finite element model was created by using the standard edentulous jaws model; its stresses and deviation were analyzed with the three-dimensional finite element stress analysis method.
方法：以标准的无牙颌模型为原形建立无牙颌全口义齿的有限元模型，运用三维有限元应力分析。
For the plates with finite dimensions, the finite element method is used to obtain the stress distribution and stress concentration around the ovaloid opening.
对于有限尺寸板内开孔的情形，文中用有限单元法来分析腰圆形孔口的应力分布和应力集中。
We ran finite element analysis stress calculations to determine where the frame needed to be reinforced for maximum strength and stiffness, then reinforced those areas with additional carbon fiber.
我们跑应力有限元分析计算，确定了框架需要得到加强的最大强度和刚度，然后加强这些领域更多的碳纤维。
After a cell is broken, the stress adjustments of the other cells in the system are obtained by finite element method using the broken cell as inner boundary.
当单元破裂后，将破裂单元作为内部边界，利用有限元方法计算由于这个单元破裂对系统其他单元造成的应力调整。
The stress and deformation of crankshaft are calculated by finite element method with six load boundary conditions and three displacement boundary conditions.
分别采用六种载荷边界条件和三种位移边界条件对曲轴应力和变形进行了有限元分析；
This finite element method is employed to analyze the behavior of eccentrically loaded CFST columns, taking initial stress degree, slenderness ratio, and eccentric ratio as the parameters.
应用该方法，以长细比、偏心率和初应力度为主要参数对有初应力的钢管混凝土偏压构件进行了受力性能分析。
With the welding spot fatigue lifetime pre-estimation method, by combination of the finite element analysis and stress calculation, the welding spot fatigue damage under actual load can be calculated.
采用焊点疲劳寿命预估方法，通过有限元分析并结合应力计算，即可计算出实际载荷工况下的焊点疲劳损伤。
According to the trial, we use finite element analysis program to conduct temperature field and thermal stress analysis of the pier under sunshine, and compared the outcome with experimental results.
根据试验采用有限元分析程序，进行日照作用下桥墩的温度场和温度应力分析，并与实验结果进行对比。
Firstly, after depicting the singularity of stress field at the top of crack, the finite element method to calculate stress intensity factor of plain fracture problems is founded.
首先，对反射裂缝尖端应力场的奇异性进行了描述，建立了平面断裂问题应力强度因子的有限单元解。
The method of analyzing the tissue stress with finite element method plays a vital role in tissue engineering.
利用有限单元法进行组织工程中的组织应力分析具有重要意义。
Possibility and efficiency in the application of this method to large finite element analysis are illustrated by an example of the stress analysis for a section of a cable stayed bridge.
以斜拉桥桥段的应力分析为例，说明在大型有限元分析中采用分阶段计算方法的可能性和有效性。
In this master thesis, the stress-strain relationships of thin films were measured by nanoindentation combined with dimensional analysis and finite element method.
本文以纳米压痕法结合量纲分析及有限元方法来测量薄膜材料的应力-应变关系。
The finite element method was used for analysis of heat stress in chip on board(COB).
本文采用有限元法分析了板上芯片（COB）的热应力分布。
The finite element method was used for analysis of heat stress in chip on board (COB).
本文采用有限元法分析了板上芯片(COB)的热应力分布。
The finite element method is used to analyze the relationship between strength and stress of the particle reinforced iron matrix composites and the shapes, sizes and fraction volume of the particles.
采用有限元方法分析了颗粒增强铁基复合材料强度和应力与颗粒形状、尺寸以及体积分数的关系。
Under the condition of three kinds of nonlinearity the stress and strain distribution of the road wheel is calculated with finite element analysis software ANSYS.
建立了负重轮的三种三维有限元力学模型，在考虑三重非线性的情况下，用ANSYS有限元分析软件计算了负重轮的应力应变分布。
The finite element analysis showed that the normal stress distribution of the grillage wall was about the same as that of the solid wall.
有限元计算表明，网格墙在轴力和水平力作用下的正应力分布与实体墙总体上一致；
Fortunately in some degree this kind of stress convergence can be eliminated or reduced to a lower level processed with the finite element equivalent stress method.
有限单元法进行拱坝分析具有诸多方面的优点，但存在较大的应力集中，而经等效应力法处理可在一定程度上削除这种应力集中的影响。
With the non-line finite element method, the numberical value calculation on the stress and deformation of surrounding rock of deep mine roadways has been presented.
采用非线性有限元法，对深井巷道围岩应力及变形状态进行了数值计算。
The finite element method is used to study the internal stress distribution condition of the KE495 engine crankshaft, then the unreasonable design of the original crankshaft is known.
利用有限元法分析KE495发动机曲轴的内部应力分布状态，得出原曲轴结构的不合理之处。
Three-dimensional finite element analysis of the stress of the mandible premolar under loading on its traumatic occlusal spots.
下颌前磨牙创伤咬合点加载的三维有限元应力分析。
Finite element method is used to study stress and place moving field inside the structure and electric measure method is utilized to verify the result of calculation.
利用有限元方法对该结构内部的应力场和位移场进行了研究。
Metbods: a two dimensional finite element model was built up to analyse the stress within the periodontal tissue of the first molar, with a reduced tooth eruption-resistant force.
方法：用二维有限元法分析阻萌力减少前后下第一磨牙牙周组织内应力分布的变化。
应用推荐