The structure of dam and foundation was analyzed in terms of 3-dimentional finite element static analysis and kinetic reaction analysis by ANSYS software.
采用ANSYS结构分析软件，对闸坝结构和地基进行三维有限元静力分析和动力响应分析。
By using multilevel substructure analysis and finite element displacement method, this system is suitable for various linear static analysis of aeronautical structures.
这一系统采用多级子结构分析技术，可以适应各种类型航空结构的线性静力分析。
Using the well-known weighted residual method and finite element procedure, a nonlinear static analysis parallel with effective stress dynamic analysis has been made.
采用著名的加权剩余值法和等参数有限单元法，对坝体进行非线性静力分析和非线性有效应力动力分析。
Theoretical analysis is done on the static and dynamic characteristics of the structure, differential equations are presented, and it is also verified by the finite element method.
同时对机构进行了静态和动态特性理论分析，提出了机构静态和动态计算解析式，并用有限元方法对机构动态和静态特性进行了验证。
This paper focuses on the use of finite element analysis software, the threshing cylinder axis static finite element analysis process.
为此，着重研究了利用有限元分析软件对脱粒滚筒轴进行有限元静力分析的过程。
Based on interval analysis and displacement finite element method, the static displacement response analysis of structure comes down to solve the interval finite element control equation.
现有的理论和方法采用区间分析和位移法有限元理论对其进行分析，最终归为位移法区间有限元控制方程的求解。
Established two typical supporting system by SAP2000 FEM software, pipe truss, cable truss. Calculation and analysis of static finite element model of these two kinds of supporting system.
采用SAP2000有限元软件建立了管桁架、索桁架两种典型支承体系有限元模型，进行了静力计算分析。
In this paper, the static analysis of Hydroplan of hydropower station engineering of Xianrendong is performed by using the finite element software of ANSYS.
本论文通过有限元分析软件ANSYS对贵州省纳雍县仙人洞水电站的厂房工程进行了结构静力分析。
Finite element analysis of derrick static force and stability. And improvement programme has been put forward.
实验井架的静力和稳定性分析，并针对存在问题提出了改进方案。
To compare the results of static and dynamic test with initial finite element model calculations, error analysis of finite element modeling has been developed.
基于试验模型的静力试验和振动试验结果与初始有限元模型计算结果的比较，展开对面向健康诊断的悬索桥有限元建模的模型误差分析。
The object oriented finite element programming is applied to a nonlinear static analysis.
把面对象有限元程序设计方法应用到非线性静态分析中。
In paper, the structural static strength and dynamic characteristic of pole? Tower of aerial power? Delivery line are analyzed and discussed with the finite element analysis.
主要利用有限元方法对架空送电线路杆塔进行结构强度和结构动力学特性分析。
Then the finite element molding process of the pulley is discussed, and the pulley is studied by the static analysis and dynamic analysis.
然后论述滚筒的有限元分析建模过程，并对滚筒做了静力分析和动态分析。
The static analysis and structural optimization of the key seal parts and components of vacuum clamp are researched in this thesis using finite element analysis software ANSYS.
本文利用通用化有限元分析软件ANSYS作为分析工具，对真空吸夹具的密封关键部位及密封元件进行了有限元静态分析和优化设计。
Bending stresses and contact stresses of the gears were investigated by finite element method in the static analysis.
在齿轮的静力学分析中，利用有限元的方法对齿轮的齿根弯曲应力和齿面接触应力进行了研究。
We have executed static analysis, model analysis and dynamic analysis on the exhaust valve in one cycle of the engine, basing on the model we founded and the finite element analysis software of ANSYS.
基于所建立的模型和ANSYS软件平台对以上的结果进行分析，分别对气门进行静力学分析、模态分析和气门一个运转周期内的瞬态动力学分析。
The stress concentration analysis was done by the finite element method and boundary element method. The fatigue strength and the strength under the static load were calculated.
对螺纹槽管进行了疲劳强度计算，并采用边界元和有限元法对螺纹槽管的应力集中进行了数值分析及静载强度计算。
A static analysis of the ribbed shell of revolution made of composite materials by using the finite element method is presented in this paper.
本文用有限元法研究了加肋和复合材料弹性旋转薄壳的静力问题。
Described are the lightening design, energy absorption car-body design, finite element analysis, static strength test and modal analysis calculation.
介绍了北京八通线地铁车体钢结构的轻量化设计、吸能车体设计、有限元分析、静强度试验和模态分析计算。
Using I-DEAS software, finite element analysis of static strength of low-sided weathering steel gondola car body is carried out.
利用I -DEAS软件，对低边耐候钢敞车车体钢结构进行有限元静强度分析。
Based on the model experiment and finite element analysis, structural static performance of a pressure spherical model with a big viewport is discussed in this paper.
结合模型试验和数值计算对大潜深、带大开口的球形耐压结构静态力学性能进行了研究。
The finite element analysis method was used to analyze the static electric field with the orthogonal design method to optimize the transducer.
采用三维有限元方法和正交试验设计方法相结合对传感器结构进行了优化设计。
The theoretical analysis of spherical bearing, the process of finite element method and theoretical static performance are presented.
给出了球面轴承的理论分析、有限元推导过程，基于有限元推导过程给出了球面轴承的理论计算静态性能。
The main subject of this thesis is about large-calibred valve. By using the finite element software ANSYS, we can do some work such as static analysis, structural optimization and fatigue analysis.
本论文以大口径闸阀阀体为主要研究对象，利用大型有限元软件ANSYS对其进行有限元静力分析、优化计算和疲劳寿命分析。
ANSYS software is used to design the axial compensator using the static electromagnetic field finite element analysis is carried out.
使用ANSYS软件对设计的轴向补偿器采用静态电磁场进行了有限元分析。
Taking a large-scale bus frame as the research object, the thesis carried out static and dynamic analysis under typical operation situation based on the finite element theory and engineering trials.
本文以一款大型客车骨架为研究对象，结合有限元理论和工程试验，进行了典型工况下的静态、动态分析。
Static analysis and modal analysis on the structure of telescope main rotary frame was achieved by means of finite element method.
利用有限元方法，完成对望远镜主转动框架的结构静力分析和模态分析。
In this paper, a finite element procedure for the nonlinear static analysis of reinforced concrete shells considering geometrical and material nonlinearities is presented.
本文采用有限元数值方法，分析计算了大型钢筋混凝土壳的几何、物理非线性静力问题。
In this paper, a finite element procedure for the nonlinear static analysis of reinforced concrete shells considering geometrical and material nonlinearities is presented.
本文采用有限元数值方法，分析计算了大型钢筋混凝土壳的几何、物理非线性静力问题。
应用推荐