Finite element mechanical model of moving crossbeam is set up for analyzing three dimension finite element intensity of this structure.
并建立了活动横梁的有限元力学模型，对该结构进行了三维有限元强度分析。
The paper USES finite element method to calculate the whole reel structure of a ship lift and presents the mechanical model of finite element analysis for the structure as a whole.
采用有限单元法对升船机卷筒结构进行整体计算，提出了有限元分析的力学模型，对筒壳、幅板的强度及刚度作了全面分析。
In this paper, APDL parameters of design and Finite Element Analysis of star gear are taken for example to research on the design, calculation and construction of the Mechanical model.
以APDL对星轮的参数化设计与有限元分析为例，先对行星齿轮力学模型进行建模，并对参数化设计计算进行研究。
A local transmitting boundary is combined with a lumped-mass finite element technique to form a mechanical model simulating the near field steady wave motion.
本文将局部透射边界和集中质量有限元技术结合起来形成一个模拟稳态近场波动的力学模型。
This paper adopts the three-dimensional finite element model, analyses the mechanical tendency with the variety of the thickness and modulus of the pavement structure.
采用三维有限元计算模型，分析了路面结构厚度和模量变化时的力学响应变化趋势。
By using the elastoplastic finite element method, mechanical model for wear tension and internal pressure resistance of casing joints is set up.
采用弹塑性有限元方法，建立了套管接头磨损拉伸与抗内压的有限元力学模型。
Using finite element method, this article presents a mathematical model and computer program for the mechanical calculation of overhead transmission lines.
本文提出了用有限元法进行架空线机械计算的数学模型和计算程序。
Using the powerful software ANSYS, the boundary condition and mechanical conditions of supporter was simulated, and a finite element analyzing mechanical model for supporter of rotary kiln was set up.
通过合理模拟回转窑托轮的边界条件和受力状况，并采用功能强大的ANSYS软件，建立了回转窑托轮的有限元分析力学模型。
The transverse elastoplastic mechanical properties of fiber bundle reinforced composites were studied by using the micro mechanical model and finite element method.
利用细观力学模型和有限元法研究纤维束复合材料的横向弹塑性力学性能。
The methods of analyzing the strength of complex mechanical structure were studied through the application of the finite element method, and the methods of building model and gridding were discussed.
研究了用有限元法对复杂机械结构进行强度分析的方法和步骤，对复杂机械结构的建模方法和网格划分进行了探讨。
A computer model for the mechanical response of steel bridge deck surfacing under wheel loading is established by using the finite element method.
采用有限元方法建立在车载作用下钢桥面铺装层的力学响应计算模型。
The finite element model of rubber dynamic auxiliary seal ring which was installed on the pusher type mechanical seal was established.
建立了滑移式机械密封装置上动态辅助橡胶密封圈的有限元模型；
It has been shown in this paper, that in solving radiation heat transfer problems for finite element model of mechanical construction it is necessary to compute the shape factor matrix.
本文说明了在用有限元模式对机械结构的幅射换热问题进行求解时，必须计算形状因子矩阵。
According to practical working situation, nonlinear dynamic finite element method is adopted to establish a numerical model of combined breaking rock with high pressure water jet and mechanical bit.
采用非线性动态有限元法，结合实际工况条件，建立了高压水射流—机械齿联合破岩的数值模型。
On the basis of finite element principle, a mechanical model is advanced for calculating the rail displacements and longitudinal forces of the welded turnout group. A computer program is designed.
基于有限单元法，建立了多组无缝道岔相联结时钢轨位移和纵向力的计算分析模型，编制了计算软件。
Based on FEM, an axis symmetric finite element electro-thermo-mechanical model in the formation of molten core of resistance spot welding is introduced.
介绍了基于有限元法模拟电阻点焊熔核形成过程中的轴对称电、热、力耦合场的模拟模型。
The mechanical hypothesis and geometry model of the composite tapes were set up. The finite element analysis models in the process of the composite tapes' shaping were established.
建立了超导复合带材的细观力学假设和模型、以及成型过程的有限元分析模型。
Through simulative analysis of finite element model and mechanical-electric coupled, the natural frequency of stator energy converter and stator's dimensions and their relation were discussed.
通过对有限元模型进行模态分析和机电耦合分析，探讨了定子换能器的固有频率和定子结构尺寸以及两者之间的关系。
According to the mechanical character of simply supported steel box girder with prestressed tendons, and considering the interaction of tendons and girder, the finite element model is established.
根据预应力简支钢箱梁的受力特性，考虑预应力索与钢箱梁的相互作用，建立了有限元计算模型，有限元计算值与实测值吻合较好。
A three dimensional elastoplastic model was established to explore the mechanical aspects of the India-Asia continental collision by finite element modeling.
用三维有限单元模型模拟了印度—亚洲大陆碰撞在板内的力学效应。
A mechanical model for finite element calculations of CA6102 engine c(?)
建立了CA6102型发动机机体有限元力学计算模型。
ObjectiveTo establish a three-dimensional finite element model and make mechanical analysis of "v" -type atlantoaxial reduction and internal fixation.
目的建立新型寰枢椎复位内固定器的三维有限元模型，并对其进行生物力学分析。
Based on the dynamic characteristics obtained with three dimension finite element method, the reduced mechanical model and parameters of lift ship structure can be modified and obtained.
利用三维有限元方法计算的结构动力特性和简化结构动力特性相等的原则修正升船结构简化力学模型，并确定了等效的升船机简化结构模型和系统参数。
The finite element model with shell element and beam element was established, the mechanical behavior of anchorage zone under the most unfavorable load was analyzed.
采用 板壳单元和梁单元建立了索 梁锚固结构的有限元模型，对索 梁锚固区在最不利荷载 组合作用下的受力性能进行了研究；
The mechanical model of composite energy storage flywheel is built based on the orthotropic elastic solid basic theory and the finite element theory.
分别基于平面应力型全弹性模型和三维数值模型建立了计算复合材料飞轮破坏转速的二维和三维算法。
A finite element model was established and the mechanical characteristics of the front and back rows of piles at different row distances were discussed.
建立有限元模型，分析了不同桩排距条件下前后两排抗滑桩的受力状况。
The FEM(Finite Element Model) analysis was used in design of the target chamber in order to optimize the mechanical design of the vacuum cone and the final optical system.
通过有限元分析方法，建立有限元分析模型，进行优化设计。
The FEM(Finite Element Model) analysis was used in design of the target chamber in order to optimize the mechanical design of the vacuum cone and the final optical system.
通过有限元分析方法，建立有限元分析模型，进行优化设计。
应用推荐