When establishing finite element calculation model of three-axle bogie frame, it must be certain that the weight of each of the three axles is equal while adding restraint.
分析了三轴转向架构架在有限元计算分析时，约束的施加必须保证三根轴的轴重一致性；分析比较了中间轴一系簧垂向刚度对构架强度产生的影响。
The calculation result is reflected into the finite element calculation model, and the durability analysis of parts is carried out according to the load of the bench experiment.
将冲压计算结果反应到有限元计算模型中，根据台架实验的栽荷，进行零件的耐久性分析。
The optimized design scheme could be found out to content requirements of design by a method combining calculation of finite element model and optimized design.
采用整体有限元模型计算与设计优化相结合的方法，可以在满足各项设计要求的条件下找到最优预应力设计方案。
Considering the boom cross section as a whole, a parametric finite element model and a parametric optimization model for local stability calculation of a boom structure were established.
将吊臂截面作为整体考虑，建立了吊臂结构局部稳定性计算的参数化有限元模型和参数优化模型。
All along, the Bucket, circular stacker-reclaimer FEM analysis, are used to design the program first, then design the finite element calculation device model based on the program.
一直以来，对于斗轮机、圆形堆取料机等大型钢结构的有限元分析，都采用先有设计方案，再在已有设计方案的基础上，建立设备的有限元计算模型进行分析计算。
At first this paper utilized the FEM software ANSYS to build the finite element model of the prototype bus body and carry on static calculation to examine the intensity of the bus body.
本文首先利用有限元分析软件ANSYS，建立原型车车身的有限元模型，进行静态计算检验车身强度。
In this paper, APDL parameters of design and Finite Element Analysis of star gear are taken for example to research on the design, calculation and construction of the Mechanical model.
以APDL对星轮的参数化设计与有限元分析为例，先对行星齿轮力学模型进行建模，并对参数化设计计算进行研究。
Strengthening method was proposed on this basis, the finite element model of strengthened bus was built and static calculation was carried out to analyze the intensity of strengthened bus.
在此基础上提出加强方案，建立加强车的有限元模型，进行静态计算分析加强车的强度，同时考察加强方案的效果与不足。
Briefly introduces the finite element model of axisymmetric field and the results of magnetic field calculation in metal.
介绍了轴对称场的有限元模型及其用于计算金属内部磁场分布的结果。
For surface crack in pipe, this paper presents the finite element model including line spring element that is used for J integration calculation, as well as numerical examples.
对管道上的表面裂纹采用线弹簧单元，建立了裂纹管道J积分计算的有限元模型，给出了J积分的计算实例。
Using the results from finite element analysis of turbine rotor suppressed in heat stress, and simplified theoretical calculation equations, a mathematical model is established.
采用汽轮机转子热应力的有限元分析结果和简化的理论计算公式，建立汽轮机转子热应力的数学分析模型。
To solve this problem, the nonlinear finite element calculation in parallel with model tests are used to study the expansion water seal, and a modified program is identified accordingly.
为解决此工程难题，应用有限元对伸缩式水封进行非线性模拟计算，同时进行模型试验，研究确定了闸门采用伸缩式水封的改造方案。
Using finite element method, this article presents a mathematical model and computer program for the mechanical calculation of overhead transmission lines.
本文提出了用有限元法进行架空线机械计算的数学模型和计算程序。
Numerical model for RTM process analysis is established by finite element method, and its calculation method is given.
本文建立了利用有限元法进行RTM工艺分析的数学模型，并给出了具体的计算方法。
And import the model into the finite element analysis software of ANSYS for modal calculation and analysis.
进而将齿轮的参数化模型导入通用有限元分析软件ANSYS，对其模态进行计算分析。
Established two typical supporting system by SAP2000 FEM software, pipe truss, cable truss. Calculation and analysis of static finite element model of these two kinds of supporting system.
采用SAP2000有限元软件建立了管桁架、索桁架两种典型支承体系有限元模型，进行了静力计算分析。
The method of establishing model in the finite element calculation can be used to the engineering calculation of machine foundations and carrying out the theoretical research.
有限元计算中提出的建模方法可以运用于机器基础的工程计算，也可运用于理论研究。
The finite element model of the supporting parts of No. 2 kiln has been established in ANSYS, and the numerical calculation has been carried out.
结合Ansys有限元分析软件建立了回转窑支承组件的有限元分析模型，并对2号窑的支承组件进行了有限元数值计算。
The article major talks about the earth seepage failure type and the theory of limited cell seepage flow calculation. And about to establish the finite element seepage flow model.
论文重点讨论了土的渗漏破坏类型和有限元计算堤坝渗流计算原理，建立有限元计算模型。
The results from centrifugal model test, field bearing test, and finite element calculation performed for the verification of the formula showed satisfactory agreement.
据室内离心机模型试验，现场载荷试验和有限元法分析的验证，它们之间符合程度是令人满意的。
It propose nonlinear dynamic analyzing model calculation method of the motor in the use of nonlinear magnetic path analysis and finite element calculation.
采用非线性磁路分析和有限元计算结合的方法给出了该电机的非线性动态分析模型计算的一种思路和方法，有助于电机设计分析。
A two-direction shear deformation finite element model is presented in which a three-dimensional problem is reduced to a two-dimensional one and thus the calculation is much simplified.
文中提出了“双向剪切变形”有限元模型，使三维问题简化为二维问题，计算工作量大为减少。
In this paper, the reactance silencer with axis symmetry is analyzed in finite element method so as to establish a mathematic model for the programming of calculation of the trans-mission loss.
通过对轴对称抗式消声器进行有限元分析，建立其数学模型，对传递损失编制程序计算。
Compared with finite element method, it needs fewer amounts of calculation and simple and convenient FEA model.
相对于有限元法计算量小，模型建立简便。
By using model test of simulated materials and finite element calculation and theory deduce, the alternate exterior entry surrounding rock stability in dynamical pressure area is systemically studied.
通过理论推导、相似模拟、数值模拟及现场测试等方法相互结合、相互补充，对动压区外错式巷道的围岩稳定性进行了较为系统的分析研究。
It is necessary to set up a 3-d finite element model and to convert the external loads acting on the hull into nodal forces of finite element in the direct strength calculation of hull structure.
在船体结构强度直接计算方法中，需要建立三维有限元模型，船体所受到的外载荷也应相应地转化为有限元节点力。
The kind of finite element model of the frame of a semi-trailer was established based on ANSYS and stress calculation and experiment validation simulating the actual working conditions were performed.
建立了基于ANSYS的某型号半挂车车架的有限元模型，并且进行了模拟实际工况的应力计算和试验验证。
A calculation model for the bridge using finite element method has been built, and the influence upon the temperature difference was analyzed.
建立了该桥的有限元计算模型，并分析了温差的影响。
The transient temperature and stress field during starting of a turbine first stage disc's 3-dimensional model has been calculated by using the general finite element calculation program ANSYS.
用通用有限元计算程序ANSYS对某燃气轮机启动过程中透平第一级涡轮盘的三维模型瞬态温度和应力场进行计算。
The transient temperature and stress field during starting of a turbine first stage disc's 3-dimensional model has been calculated by using the general finite element calculation program ANSYS.
用通用有限元计算程序ANSYS对某燃气轮机启动过程中透平第一级涡轮盘的三维模型瞬态温度和应力场进行计算。
应用推荐