By comparing the results obtained from the test and finite element analysis, a very good agreement is found, showing the accuracy and feasibility of the simulation with finite element method.
将有限元模拟结果和试验结果进行了比较，取得了较好的一致，验证了有限元分析的正确性和可行性。
We ran finite element analysis stress calculations to determine where the frame needed to be reinforced for maximum strength and stiffness, then reinforced those areas with additional carbon fiber.
我们跑应力有限元分析计算，确定了框架需要得到加强的最大强度和刚度，然后加强这些领域更多的碳纤维。
The modal and harmonic response analysis of the structure were implemented using the finite element analysis method with ANSYS software.
使用有限元分析软件ANSYS对结构建模，并进行模态和谐响应分析。
In this thesis based on engineering examples, some Suggestions were put forward to control crack by finite element analysis of floor slabs.
本文结合工程实例，对楼板的温度裂缝进行了有限元分析，并提出了一些预防裂缝的建议。
The correct weak form of basic equations in elasticity is the foundation of finite element analysis.
弹性力学基本方程正确的弱形式将是有限元分析的基础。
Mesh generating is a necessary procedure between geometric definition of part and its finite element analysis.
有限元网格生成是零件几何定义和有限元分析之间必不可少的步骤。
Corrugation problem in the car trunk sealing strip edges is analyzed with the highly non-linear finite element analysis software (MARC). The structure and material is optimized.
本文利用高度非线性有限元分析软件MARC分析轿车行李箱密封条唇边的起皱问题，并对其结构及材料进行了优化。
The analysis result shows that it is a very feasible method for designing of nonstandard parts to adopt optimal technology based on finite element analysis.
分析结果显示，将基于有限元分析的优化技术应用于非标零件的设计是一种非常可行的方法。
Considering characteristics of grotto relics the influence factors and dynamic finite element analysis methods on deformation stability grotto country rock are discussed.
针对石窟文物的特点，阐述了影响石窟围岩变形稳定性的主要因素和动力有限元分析方法。
A finite element analysis demonstrated that minimizing bone and ligament removal resulted in greater preservation of normal motion of the lumbar spine after surgery32.
有限元分析证实，最低程度的切除骨和韧带能够更大程度的保留术后腰椎正常活动范围32。
Conclusion Three dimensional finite element analysis is a kind of convenient and practicable method to be used as the confirmation and supplement of experimental biomechanics study of human being.
结论三维有限元分析方法是一种简便实用的生物力学研究方法，可作为实验生物力学研究的验证和补充方法。
In the process of completing, the mechanism design requests are considered fully, some methods such as the computer assistant simulation design, finite element analysis and test verify are adopted.
在完成过程中，充分考虑了铺设轮的机械设计要求，采用了计算机辅助仿真设计、有限元分析和试验校验的方法。
Complete finite element analysis is conducted on pile frame of SYR200 rotary pile drill with the model, which provides guiding reference for the design of pile frames.
使用这种模型对SYR200旋挖钻机桩架进行了整体有限元分析，分析对钻孔机桩架的结构设计有指导意义。
According to the trial, we use finite element analysis program to conduct temperature field and thermal stress analysis of the pier under sunshine, and compared the outcome with experimental results.
根据试验采用有限元分析程序，进行日照作用下桥墩的温度场和温度应力分析，并与实验结果进行对比。
With the welding spot fatigue lifetime pre-estimation method, by combination of the finite element analysis and stress calculation, the welding spot fatigue damage under actual load can be calculated.
采用焊点疲劳寿命预估方法，通过有限元分析并结合应力计算，即可计算出实际载荷工况下的焊点疲劳损伤。
And ANSYS is a large scale general finite element analysis software with abroad application.
而ANSYS是得到广泛应用的大型通用有限元分析软件。
Program design: to work out a utility analysis Program is the absolutely necessarily tache of finite element analysis, and also is this discourse's finally aim.
程序编制：编制出实用的分析程序是有限元分析课题必不可少的环节，也是本文的最终目的。
Possibility and efficiency in the application of this method to large finite element analysis are illustrated by an example of the stress analysis for a section of a cable stayed bridge.
以斜拉桥桥段的应力分析为例，说明在大型有限元分析中采用分阶段计算方法的可能性和有效性。
The effects of disuse on trabecular bone structure was simulated, using the bone (re) modeling model with goals of physiological regulation, based on finite element analysis.
本研究将有限元分析与带有调整目标的骨再造方程相结合，模拟废用对松质骨结构的影响。
The strength, rigidity, stability and torsional rigidity of the bodywork structure were calculated by using finite element analysis. Thus the optimum fillet of the bodywork structure can be specified.
采用有限单元法对车体结构的强度、刚度、稳定性、挠跨比、扭转刚度进行计算，为车体设计提供了参考依据。
Under the condition of three kinds of nonlinearity the stress and strain distribution of the road wheel is calculated with finite element analysis software ANSYS.
建立了负重轮的三种三维有限元力学模型，在考虑三重非线性的情况下，用ANSYS有限元分析软件计算了负重轮的应力应变分布。
This paper focuses on the use of finite element analysis software, the threshing cylinder axis static finite element analysis process.
为此，着重研究了利用有限元分析软件对脱粒滚筒轴进行有限元静力分析的过程。
To examine the monitoring results, the finite element analysis is used to calculate the effect between jacked piles and soil.
为了测斜仪技术检验监测结果的准确性，采用有限元分析方法计算静压桩与土的相互作用效果。
ANSYS is a general finite element analysis software. And mesh dividing is an important part of finite element analysis with ANSYS.
ANSYS是一个大型通用的有限元分析软件，网格划分是利用ANSYS进行有限元分析的一个重要环节。
The seismic capacity of the box-shaped joint in the reinforced concrete mega-frame structure system is studied, and the finite element analysis is done with ANSYS .
本文对钢筋混凝土巨型框架结构箱形节点抗震性能进行了试验研究及ANSYS程序有限元分析。
The driving wheel's axle is a key parts of the billet transport vehicle, so the axle's stress and deformation were analysed by the structure finite element analysis software ANSYS.
主动车轮轴是钢坯运输车的关键零部件，采用结构有限元分析软件ANSYS分析了该轴的应力和变形。
The driving wheel's axle is a key parts of the billet transport vehicle, so the axle's stress and deformation were analysed by the structure finite element analysis software ANSYS.
主动车轮轴是钢坯运输车的关键零部件，采用结构有限元分析软件ANSYS分析了该轴的应力和变形。
应用推荐