Based on the filling characteristics of LPDC wheel castings, a simplified mold filling simulation software was developed.
针对轮毂铸件的充型特点，开发了简化充型模拟软件。
A homemade 3d filling simulation package-HSCAE 3drf was applied to optimize the mold structure and process of the front-board of Haier's net-air-condition.
应用国产三维流动模拟软件HSCAE3drf对海尔空调前面板的注射模具结构及工艺进行优化。
Simulation results show a smooth filling, uniform temperature distribution and few flaws such as gas inclusion and cold shut. A casting with a good quality was obtained.
模拟结果表明，该浇注系统填充过程平稳，温度场分布均匀，所得压铸件气体夹杂和冷隔缺陷少，整体质量较高。
Numerical simulation of filling and solidification of large aluminum alloy support frame in indirect casting was conducted based on FDM.
基于有限差分法，对大型铝合金支架间接挤压铸造充型和凝固过程进行了数值模拟。
By the aided of numerical simulation technique we can not only accurate picture the cavity filling process also can predict moulding fault among the die casting et al.
借助于数值模拟技术不仅能较准确的描述铸液的充型过程，而且能预测铸件内部的成型缺陷等。
This paper studies the filling characteristic of the ring shape runner system based on the Large Qrifice Discharge theory and takes the hydraulic simulation test.
本文根据大孔出流理论。对环形横浇道系统的充填特性进行了研究与水模拟试验。
Through the experimental simulation of RIM mold filling with low viscosity fluid, the formation of air bubbles in RIM process was studied.
通过反应注射成型冷态充模模拟，考察了充模过程中各种气泡的形成过程。
The technology of numerical simulation on filling process of castings is a frontal technology in the casting field.
铸造充型过程的数值模拟技术是铸造领域的前沿技术。
The optimization on the filling and solidification process of CY-61100 lathe tailstock casting was conducted by numerical simulation.
对CY- 61100车床尾座铸件充型及凝固过程进行了数值模拟及优化研究。
Three-dimension fluid field coupled with temperature field numerical simulation program was debugged. And worked out, three-dimension mold filling course can bitterly numerical simulated.
编制调试了三维充型过程的流场、温度场耦合数值模拟计算程序，能够较好地数值计算模拟铸件三维充型过程。
A coaxial hybrid wiggler free-electron laser (FEL) amplifier with and without plasma filling is studied by a method of PIC simulation in this paper.
采用PIC模拟方法对同轴混合铁磁摇摆器自由电子激光器进行了研究，分析了等离子体填充对其性能的影响。
Using the analogy simulation, an experimental study of physical simulation about semisolid slurry's out flow from the stirring crucible and the filling state of the die chamber is carried out.
利用相似模拟的方法，进行了半固态浆料自搅拌坩埚的出流及压室充填状况的物理模拟实验研究。
The latest progress on numerical simulation of mold filling and solidification processes of shapedcasting was reviewed.
概述了铸件充型及凝固过程数值模拟研究的最新进展。
Combining the computer simulation with X-ray real time observation, view-cast is a novel technique used for optimizing design of filling system.
它是指将计算机模拟与X射线实时观察相结合，进行铸件浇注系统优化设计的新技术。
The simulation results show that the rule-adaptive fuzzy control has better static and dynamic performances, and follows filling curves very well and ADAPTS to the changes of process parameters.
仿真结果表明，规则自适应模糊控制具有较好的动态和静态性能，不但具有很好的工艺曲线跟踪性能，而且对过程参数的变化有很强的适应性。
The results indicate that the presented method can work well in the simulation of the two-phase flows of the filling processes of three dimensional complex castings.
结果表明：投影。水平集方法能够较好地模拟三维复杂铸件充型过程的两相流动。
Numerical simulation analysis is made of the paste piping transportation using FLOTRAN CFD calculation hydrodynamic analysis module in ANSYS software based on the paste filling mechanical parameters.
以膏体充填力学参数为基础，运用ANSYS软件中的FLOTRANCFD计算流体动力学分析模块对膏体管道输送进行了数值模拟分析。
Based on the previous explicit algorithms for the simulation of filling process, a new explicit and vectorial algorithm for bi-phasic flow is proposed and developed.
基于模拟填充过程显式算法，提出用于模拟双相流的全矢量化运算显式算法。
The dynamic response of fresh concrete filling pile under blasting load is studied by numerical simulation in this paper.
采用数值模拟方法，对新浇混凝土灌注桩在爆破振动作用下的动态响应进行了分析。
The theoretical model and research status of the simulation of powder injection molding filling process are reviewed. Their merits and demerits are analyzed and compared.
综述了目前用于粉末注射成形充模流动模拟所采用的理论模型及其应用研究现状，并对各自的优缺点进行了分析。
The numerical methods in the simulation of mold filling process are introduced. The main trends and directions are proposed.
介绍了粉末注射成形充模流动模拟所采用的数值计算方法，展望了该技术的发展趋势和方向。
The mathematical model of numeric simulation of casting filling and solidification process were studied.
对铸造充型及凝固过程数值模拟的数学模型进行了研究。
The numerical simulation technique of mould filling process is a frontal technique of foundry technology.
铸造充型过程的数值模拟技术是铸造领域的前沿技术。
Surface simulation test of this filling technology was carried out in Dachang Tongkeng Tin Mine for the first time in China. The results were described in this paper.
本文介绍的是在大厂铜坑锡矿进行的国内首例块石砂浆胶结充填的地表模拟试验情况。
Process simulation studies include formulation (compounding), filtration and filling with suitable media.
工艺模拟研究包括用合适的介质进行配方（组成），过滤和灌装。
Numerical simulation predicts molten metal velocity field and temperature field in the filling progress. Filling of casting thus is be evaluated.
数值模拟预测了金属液充型过程的流动速度场和温度场，并对充型过程进行了评价。
The numerical simulation of the filling stage in gas-assisted injection molding can give an instruction to product, so the precision of the result is important.
数值模拟的气体辅助注射成型充填阶段，可以给一个指令的产品，这样的结果的精度是非常重要的。
The finishing die was designed. According to finite element numerical simulation method, the filling state, load prediction and bending deformation of the local finishing process were obtained.
设计了局部精整模具，并应用有限元数值模拟方法分析了局部精整成形过程中的充填情况、成形载荷以及弯曲变形的规律。
Image information of filling process was observed and recorded by computer video technology for hydraulic simulation based on physical simulation, image treatment and computer application.
以物理模拟技术、图像处理技术和计算机技术为基础，采用水模拟计算机可视化技术，观察和记录液体充型过程的图像信息。
Computer simulation was employed to optimize filling system to predict filling process and prevent the defects for al alloy automotive parts in semi-solid die casting.
在试制铝合金半固态压铸汽车零件过程中，引入计算机模拟技术用于充型过程的预测与缺陷的预防，实现了充型工艺系统的优化设计。
应用推荐