The interaction mechanism of fiber-fiber and fiber-matrix is emphasized in this paper.
本工作着重分析复合材料中纤维与纤维、纤维与周围基体的相互作用机理。
It is shown that the fiber can considerably resist the matrix creep along the axial direction, but not so for transversely and shear deformation.
研究表明,纤维在轴向对基体的蠕变起到明显阻止作用,而在横向和剪切变形下的作用较小。
It becomes clear, then, that adhesion of the fiber and the matrix at the composite interface is fundamental to the failure of the composite.
这样,显然,复合材料界面上的纤维与基体的粘接是复合材料失效的基础。
The effects of volume fraction, cross section shape of fibers and the relative thermal conductivity of fiber and matrix on thermal conductivity of composites are analyzed in this thesis.
本文通过计算结果比较,分析了复合材料体分比、纤维截面形状、纤维与基体的相对导热系数对复合材料整体导热性能的影响。
On the basis of the transfer matrix theory, the authors have studied the transmission properties of the sampled chirped fiber grating.
运用传输矩阵理论,对取样啁啾光纤光栅的传输特性进行了模拟研究。
The influences of the fiber substrate pretreatment process and matrix densification methods on the properties of carbon fibers reinforced silicon carbide composites have been investigated.
研究了炭纤维编织增强体的预处理工艺和基体致密化工艺对炭纤维增强碳化硅基复合材料性能的影响。
Reflective spectral properties of sampled fiber Bragg grating is theoretically calculated by transfer matrix method.
用传输矩阵法从理论上计算了取样光纤布拉格光栅的反射谱特性。
The thermal residual stresses can be indicated as a function of the properties of fibers and matrix materials and geometry of twisted fiber bundle.
这种热残余应力可以表示为纤维、基体材料性质以及纤维束几何参数的函数。
Steel fiber is often used to reinforce cemented materials because it can provide bridging effect of crack in matrix.
钢纤维因其能为基体裂纹提供桥联而经常被用于增强水泥基材料。
Under the paraxial approximation, the optical transformation matrix of the upside down taper lens fiber end is given.
在近轴近似下,给出了这种光纤端的光学传递矩阵。
The effects of atomic coherence on fiber amplifiers pumped by two lasers with different frequences are studied by using density matrix theory.
用密度矩阵的方法从理论上分析了不同频率的两个激光场混合泵浦的光纤放大器中,由光场诱导的原子相干效应。
The cross section aspect ratio of fiber and the distribution of matrix surrounding are taken into consideration in the model.
该模型考虑了纤维截面的纵横比及基质在纤维周围的分布,对所有纵横比的情况都适用。
Based on the testing results, the influence of matrix strength grades and fiber geometry on shear behaviors was discussed and the mathematics model of shear behaviors was established.
根据实验结果,探讨基体强度等级和纤维外形对混凝土抗剪性能的影响,并根据材料复合理论建立起钢纤维混凝土抗剪性能的数学计算模型。
Based on the testing results, the influence of matrix strength grades and fiber geometry on shear behaviors was discussed and mathematics model of shear behaviors was established.
根据实验结果,探讨基体强度等级和纤维外形对混凝土抗剪性能的影响,并根据材料复合理论建立起钢纤维混凝土抗剪性能的数学计算模型。
It was concluded that the interlaminar tensile strength of the composite is dominated by the bonding strength of the interface between fiber and matrix, not by lay-up orientation.
结果表明:该复合材料层间拉伸强度较少受到铺层取向的影响,而由纤维与基体的界面结合强度所控制。
Mechanical propertys of fiber composites largely depend on stress transfer of fiber and matrix.
纤维复合材料的力学特性很大程度上依赖于纤维和基体的应力传递。
It is assumed that the elastic fiber bundle is evenly distributed in the elastoplastic powerlaw hardening matrix and the contact between fibers in the fiber bundle is smooth.
假设弹性的纤维束均匀地分布于幂硬化弹塑性基体材料中,并假设纤维束内的纤维接触是光滑的。
A new kind of fiber reinforced composite was prepared by using continuous basalt fiber as reinforcing agent and vinyl ester resin as matrix.
以连续玄武岩纤维为增强剂,乙烯基酯树脂为基体,制备了新型纤维增强树脂基复合材料。
A new type of friction material was prepared with carbon fiber and steel fiber as reinforcements and FB polymerized phenolic as matrix resin by mould pressing technology.
采用碳纤维和钢纤维为增强材料、硼酚醛树脂为基体,通过模压成型制得新型混杂纤维增强树脂基摩阻材料。
A pretreating method for waste nylon 6 short fiber was proposed to improve the adhesion between short fiber and waste PP matrix and the dispersion of short fiber in matrix.
出一种废尼龙6短纤维预处理方法。采用这种方法能提高短纤维与废pp基质的粘合性能并改善短纤维在基质中的分散。
Also the microstructures at the interface of fiber and matrix were observed and analyzed through TEM.
用透射电子显微镜观察分析了增强体与基体合金界面的微观组织结构。
The interfacial structure of graphite fiber reinforced magnesium matrix composites becomes complex because of the addition of al into the matrix.
石墨纤维增强镁基复合材料由于基体中加入了铝元素,其界面情况变得较为复杂。
On the basis of elastic mechanics theory, the micro residual stress expression of matrix around fiber in metal matrix composites is deduced.
根据弹性力学理论建立了纤维增强金属基复合材料中纤维周围基体中的残余热应力模型。
In this paper, the properties and preparation of ceramic short fiber reinforced al si alloy matrix composite and it is application to the piston of internal combustion engines are reported.
本文报导了陶瓷纤维增强复合材料的性能、制备研究及其在内燃机活塞上的应用。
In this paper, the surface treatment of carbon fiber and the research progress on the fabrication and properties of the carbon fiber reinforced copper matrix composites are introduced.
介绍了炭纤维的表面处理,炭纤维增强铜基复合材料的制备工艺与性能的研究进展。
In a composite system, the adhesion at the interface between fiber and matrix plays an important role in improving the resulting mechanical behavior.
良好的界面粘结是制备高性能复合材料的关键之一,而树脂与纤维的优良浸润则是其首要前提。
The traditional shear lag theory of stress transfer in short fiber reinforced metal matrix composites was modified and improved.
对短纤维增强金属基复合材料应力传递的传统剪滞理论进行了修正和改进。
The static fatigue behaviors of unidirectional short fiber reinforced glass ceramic matrix composites under different medium were investigated.
研究了不同介质中单向短纤维增强玻璃陶瓷基复合材料的静疲劳行为。
Infiltration process of fiber reinforced magnesium aluminium matrix composites made by liquid infiltration was mainly studied in the paper.
本文着重研究了液态浸渗法制备纤维增强镁、铝基复合材料的浸渗工艺。
The changing regularity of the deformation and compliance of resin matrix composites with the fiber orientation has been discussed.
讨论了树脂基复合材料的柔度和变形随纤维方向的变化规律。
应用推荐