Both units include a 2 - by 9-inch feed opening; a new waste-evacuation, dust-collection system; and a new cabinet for quieter operation.
两个机器都包含了2- 9英寸加料口，还有个废纸处理器、灰尘处理系统、和一个新的消音装置。
The material to be crushed is fed into machine from the feed opening of top, and fall down onto the central section of rotor rotating with high speed.
待破碎物料从顶部的物料投入口投入，落到高速旋转的转子中心部位。
When more than one feed opening is required, the flow rate of each feed inlet must be carefully adjusted so as not to exceed the total capacity of the conveyor.
当需要开启一个以上进料口时，必须小心地调节限制每个进料口的流量，以使其总量不要超过输送机的设计能力限。
The air inlet of the air inducing system of the equipment is arranged right above the slicing device, and the feed opening of the cyclone separation system is arranged right below the slicing device.
该设备的引风系统的进风口位于切片装置的正上方，旋风分离系统的进料口位于切片状置的正下方。
She can look into what recently happened in the team by opening the All events for this team area feed available in the Artifacts section of the team area editor.
通过打开团队区域编辑器的Artifacts部分中可用的AlleventsforthisteamareaFeed，她可以查看团队中最近发生的事情。
This paper focuses on effects of the valve characteristics and the transfer pipe delay on dynamic performance for boiler drum level, under varying valve opening of the feed water control valve.
本文着重探讨当给水调节伐门开度变化时，伐门特性以及管路传输迟延对锅炉汽包水位动态特性的影响。
The process of jet mixing in the reactor was studied with tracer technique and the effects of the opening structure on the wall of the feed ring and the momentum ratio to the jet mixing were analyzed.
文中采用示踪法研究了四氯化钛氧化反应器内径向射流混合特征，探讨了射流环开孔结构和动量比等因素对射流混合效果的影响。
Feeder has a rounded front forming an elliptical arc in relation to the back with a feed access opening in the front.
直属前面有一个圆形形成就与前方饲料打开后门进入椭圆弧。
The traditional 3-layer feed forward BP network modal of morphological opening and closing operation was modified by extending the input layer data.
采用扩展输入层数据的办法修正了传统的形态开、闭运算三层前馈BP网络模型。
According to process parameters given by level 2 model, TCS system changes gap opening of vertical edging rolls to control strip width through feed forward and feedback technology.
通过前馈和反馈技术，TCS按照二级模型给出的工艺参数实时变换立辊开口度来控制带钢的宽度。
Bales of fiber are placed into some type of automatic fiber feed unit. Metal fingers pull tufts of fibers from the bale. These fibers are fed to the opening, cleaning and blending area;
棉包被放置在某种自动喂棉机上，金属抓棉刀片从棉包中抓取棉块，然后将棉块送至开清棉区；
Bales of fiber are placed into some type of automatic fiber feed unit. Metal fingers pull tufts of fibers from the bale. These fibers are fed to the opening, cleaning and blending area;
棉包被放置在某种自动喂棉机上，金属抓棉刀片从棉包中抓取棉块，然后将棉块送至开清棉区；
应用推荐