Also analyzed are the deformation characteristics of the metal when conical roll is used and there exist both toe Angle and feed Angle.
分析了采用锥形轧辊，在辗轧角和送进角同时存在时金属的变形特点。
Relevant operation shows that owing to the change of the feed Angle piercing efficiency has been increased, net rolling time reduced, and unit energy consumption lowed.
生产实践表明，送进角改进后穿孔效率提高，纯轧时间减少，单位能耗降低。
From the model, the effects of the dip Angle and feed rate on thrust force are estimated.
在此基础上，分析比较了进给量、斜面倾角等参数对斜面钻孔初期受力的影响。
The results show that the effects on surface roughness are feed speed, depth of cutting , tool rake angle and parts hardness in turn.
结果表明：工件进给速度对表面粗糙度的影响最大，切削深度和刀具前角次之，工件硬度影响最小。
The feed equipment of impact crusher was improved. A rational structural and simple feeding device was designed. It can be connected with the impact crusher at any Angle in the horizontal position.
对机械冲击式粉碎机的进料装置进行改进，设计了一个结构合理、简单的进料装置，可在水平位置按任意角度连接在冲击式粉碎机上。
The effects of tool's inclination angle on chip formation and the temperature fields, as well as the cutting forces, back forces and feed forces are discussed.
通过三维切削模拟可以获得在不同刃倾角精密切削过程的条件下切屑形状、切削力和切削温度场的分布情况。
In this system the crankshaft rotating Angle, where the peak combustion pressure occurs, is taken to be a feed back signal, so that the ignition timing of the engine is able to be controlled.
该控制系统利用最高燃烧压力点的曲轴转角作为反馈信号，实现其对发动机点火正时的控制。
This paper presents the information of the effect, measured with a tele-strain-meter, of work material, feed, cutting speed, depth of cut, number of teeth and helix Angle etc.
本文在高速滚齿机上，利用遥测应变仪，测定了工件材料，进给量，切削深度，切削速度，齿轮齿数及螺旋角等对力矩的影响，并得出径节为8时的力矩公式。
Vibrating direction Angle and motor speed has great impact on the vibrating system and stuff feed speed of grain clearing equipment.
振动方向角和电机转速对粮食清理设备的振动体制和物料推进速度有很大影响。
No matter what the Angle, holes keep food on the spoon longer so your child can learn to self-feed successfully.
无论是什么角度看，孔保持食物对填鸭式不再让你的孩子可以学会自我饲料成功。
Based on the principles that lateral offset-focus feed makes the antenna pattern deflect an angle, the multi-beam antenna can be used in passive imaging system.
本文首先分析了焦平面阵列馈源横向偏焦产生多波束的原理，并采用面电流法对偏焦抛物面天线方向图进行了编程计算。
Basing on the optimal control theory, the DYC controller is designed by the feed forward of the sideslip Angle regulation and the state feedback of both yaw rate and sideslip Angle.
基于最优控制理论，设计横摆力矩控制器，通过前馈控制调整侧偏角，状态反馈控制调整横摆角速度和侧偏角。
By the feed-back control of the duty ratio according to the oscillations of the movable plate, the movable plate can be controlled to oscillate in the proper phase and at the proper oscillation Angle.
通过根据可移动板的振动对占空比的反馈控制，可控制可移动板以在适当的相位和适当的振动角振动。
By the feed-back control of the duty ratio according to the oscillations of the movable plate, the movable plate can be controlled to oscillate in the proper phase and at the proper oscillation Angle.
通过根据可移动板的振动对占空比的反馈控制，可控制可移动板以在适当的相位和适当的振动角振动。
应用推荐