Based on FEA simulation, design of composite subway station is mere effective and appropriate.
复合式地铁车站以有限元数值模拟结果可为结构设计提供参考依据。
At last the article summarize FEA simulation results in some points and explain methods for determining best spin testing speed of impeller.
总结了叶轮最佳超速转速的确定方法，以确定经有限元分析的实际叶轮的最佳超速转速。
One of the key technique problems is boundary dynamic contact constraint and contact judgment in FEA simulation for 3d complicated massive forming.
边界界面动态接触约束与接触判断是3维复杂体积成形有限元数值模拟的关键技术问题之一。
Simultaneously, the forming process of claw-pole was studied with numerical simulation and FEA method, property parameters and relative field information during the forming process were also obtained.
同时，采用数值模拟和有限元分析的方法获得了成形过程的力能参数和相关的场量信息。
The simulation and analysis of the pressure distribution in head runner of double plex tread extruder were made with ANSYS FEA software.
采用ANSYS有限元分析软件对胎面双复合挤出机头流道内部的压力场进行模拟和分析。
The 3-d pump model cannot only be used in assembly, intervene inspection and process simulation, but also provide computational model for FEA and CFD.
泵的三维模型不但可以用于零件装配、干涉检查、加工模拟，而且可以为有限元分析(FEA)和计算流体动力学(CFD)分析提供计算模型。
The simulation on medium frequency induction hardening process of crankshaft in 6110 engine is carried out by using FEA software ANSYS with hardening depth predicted and residual stress calculated.
利用A NSYS有限元分析软件，进行了6 110钢曲轴的中频感应淬火过程的模拟计算，并预测了淬硬层的深度，计算了淬火后的残余应力分布。
Abstract: Several method are brought forward in order to improve the computation efficiency of the FEA of sheet forming. The Influence of virtue speed on the numerical simulation is also investigated.
文摘：主要介绍了提高板料成形有限元分析计算效率的几种方法，并通过实验研究了虚拟速度对有限元分析结果的影响。
Static strength of the frame side rail was examined by numerical simulation using the FEA code MSC-NASTRAN with results verified by the test.
针对轻型货车在行驶过程中纵梁撕裂的问题，应用有限元分析软件对车架的强度进行了分析，并通过实验的方法证明了计算模型的正确性。
With the comparison of FEA data and actually measured data of the seismic desk simulation experiment, the validity of calculation model of this bridge and dynamic analysis has been validated.
通过与模型振动台试验的实测值进行了对比分析，验证了建立的计算模型及动力分析方法的正确性。
Several method are brought forward in order to improve the computation efficiency of the FEA of sheet forming. The Influence of virtue speed on the numerical simulation is also investigated.
主要介绍了提高板料成形有限元分析计算效率的几种方法，并通过实验研究了虚拟速度对有限元分析结果的影响。
This simulation includes the following steps: with the use of ANSYS software package, the attraction characteristic of contactor with permanent magnet is simulated, which is based on FEA model;
该分析包含如下步骤：建立有限元模型应用ANSYS软件包仿真研究永磁式接触器的吸力特性；
This simulation includes the following steps: with the use of ANSYS software package, the attraction characteristic of contactor with permanent magnet is simulated, which is based on FEA model;
该分析包含如下步骤：建立有限元模型应用ANSYS软件包仿真研究永磁式接触器的吸力特性；
应用推荐