Take part in the design review during equipment fabrication phase and assist the on-site validation and installation of extrusion equipment.
在设备制作阶段和外国的设备供应商一同进行设计评估。并协助设备的现场验证和安装。
The company will support an alternative warhead (AW) integration and demonstration phase that includes the warhead fabrication and integration with the GMLRS as well as flight testing of the rocket.
Aerojet公司将支持可替换弹头的集成和演示阶段，包括弹头制造以及与GMLRS集成，同样包括集成后的测试。
Fabrication of the Bragg grating in a highly nonlinear photonic crystal fiber was investigated experimentally by phase mask method.
采用相位掩模版法实验研究了高非线性掺锗光子晶体光纤中布拉格光栅的制作。
Furthermore, the paper offers the error limited of these parameters and they are good to guide practical fabrication of the volume phase holographic grating.
同时，本文还计算出了这几种参数的误差容限，这对体积相位全息光栅的实际制作具有指导作用。
And there is much more phase delay, when the fabrication excursion is perpendicular to the incident wave polarized direction.
当装配偏移方向与入射波极化方向正交时，出现较大相位延迟。
Using only one optic element, the phase mask provides a robust and inherently stable method for reproducing fiber Bragg gratings, and reduces the complexity of the fiber grating fabrication system.
由于相位模板法仅使用一个光学器件，因而减少了光纤光栅制造系统的复杂性，是光纤布拉格光栅写入法中最有前途、使用最广泛并且具有本征稳定性的一种方法。
The correlations between dispersing phase mean diameter and water addition rate, emulsified agent and fabrication parameters were given by the experiments as well.
实验也给出了分散相的平均直径与掺水率、添加剂用量和制备参数的关系。
Useful information has been resulted for the practical fabrication of the phase mask.
这些都为相位掩模的实际制作提供了有意义的结果。
Described are principles, applications and fabrication process of conventional masks and phase-shifting masks with sub-resolution pattems.
介绍亚分辨图形掩模的原理、应用及具有亚分辨图形的相移掩模和传统掩模的制作方法和工艺。
The fabrication of FBG in four different type photosensitive fiber through phase mask is finished successfully and the photosensitivity of the four-type fiber is studied.
采用相位掩模法在四种不同的光敏光纤中成功写入布拉格光纤光栅，并对四种光纤的光敏性进行了研究；
With that mask, an improved procedure on fabrication of phase type CGH is also presented.
利用掩模板，本文同时展示了一种加工位相型CGH的新工艺流程。
An equivalent circuit model of these 3-phase unidirectional transducers is discussed as well as their adjustment and fabrication.
本文讨论三相单向换能器等效电路模型和制作调整。
Mould release agents cannot be used in the fabrication of this part because it must undergo another bonding phase which requires a clean application surface.
为了防止给下面的工序造成污染，因此不能使用脱模剂。
The effect of the phase-change cooling mirror will depend on the fabrication.
镜体的结构决定了相变致冷镜抑制腔镜在高能激光辐照下的热变形的效果。
The effect of the phase-change cooling mirror will depend on the fabrication.
镜体的结构决定了相变致冷镜抑制腔镜在高能激光辐照下的热变形的效果。
应用推荐