In this article, we discuss typical modeling errors that we extracted from hundreds of real-world process models created in different tools.
在本文中，我们讨论了从数百个用不同工具创建的流程模型中提取而来的典型建模错误。
A well-formed nesting of cyclic and branching process fragments is a good approach to reduce the possibility of modeling errors.
设计形式良好的循环嵌套和流程片断分支，将是降低出现建模错误的可能性的有效方式。
This anti-pattern is also one of the most frequent modeling errors.
此反模式也是最常见的建模错误之一。
For example, model validation will catch errors such as incorrect modeling of C# delegates.
举例来说，模型验证会捕获例如对 C#委托的不正确的建模的错误。
These patterns lead to a well-formed structure for the models, which avoids many modeling errors that otherwise occur when gateways are used in an arbitrary way.
利用这些模式，可设计出形式良好的模型结构，从而避免因随意使用网关而导致的建模错误。
In this article, we investigate typical modeling errors that we extracted from hundreds of real-world process models drawn in different business process modeling tools over the last two years.
在本文中，我们研究了过去两年中根据从不同建模工具中挑选出的数百个真实流程模型总结的典型建模错误。
The modeling errors are grouped into six common modeling scenarios.
建模错误被分为六种通用建模场景。
Data-flow errors typically arise when data is flowing along several execution branches that can either capture alternative or parallel behaviors. This produces three modeling situations.
数据流错误一般出现在数据沿几个执行分支流动的时候，这些执行分支可以捕获可选或并行行为。
Both control laws do not require the knowledge of the system parameters and are robust to modeling errors.
两种控制律不需要知道系统参数，对模型误差具有鲁棒性。
The image-based approach may reduce computational delay, eliminate the necessity for image interpretation and eliminate errors due to sensor modeling and camera calibration.
该方法可以减少计算延时，并且对摄像机和机械臂的校准误差和目标模型误差具有较强的鲁棒性。
This model is never an exact representation of reality, since modeling errors are inevitable.
模型不是一个准确的实体表现，模型的误差是不可避免的。
However, little has been done on the generalized mathematical modeling of locating errors, especially for angular dimensions.
但对定位误差通用计算模型的研究涉及甚少，而对角向尺寸定位误差通用建模的研究则更少。
The model and conclusion can be applied to the modeling and compensating of errors of multi-axis CNC machine tools.
所提出的模型和结论，可推广应用于多轴数控机床的误差建模与补偿。
A new method of robust controller design has been developed on the basis of soft-bound description of modeling errors.
本文基于对系统建模误差的软边界描述，提出了一种新的鲁棒设计方法。
The errors of the modeling prototypes against its sample parts got in reverse engineering modeling have direct influences on the performance and quality of the reversed products.
逆向建模得到的原型和实物样件之间的误差，直接影响了逆向产品的性能和质量。
We propose methods for modeling errors and detect network anomalies.
我们提出了建模误差和检测网络异常的方法。
Based on observer method, an algorithm of actuator fault detection and diagnosis is presented for a class of nonlinear control systems with system modeling errors and sensor modeling uncertainties.
针对一类具有系统建模误差以及含传感器模型不确定项的非线性控制系统，本文提出了一种用于执行器故障检测与诊断的观测器方法。
We build models and make predictions for the currency exchange rate, the prediction errors of adaptive modeling method decrease.
对外汇汇率问题进行的模型构造和预测的结果表明，该方法的预测误差明显减小。
Internal model control is proposed for the compounded pseudo-linear system. The robust stability of the closed-loop system with modeling errors is analysed.
针对复合后的伪线性系统采用内模控制，分析了存在建模误差的情况下闭环系统的鲁棒稳定性。
Though there are errors during the modeling for the robot dynamics, they can be compensated according to the rule of adjusting weight values.
在机器人动力学方程存在误差的情况下，能通过文中提出的参数调整规则补偿误差。
A grouping optimization modeling for the thermal errors of NC machine tools was presented.
提出数控机床热误差分组优化建模。
The method was used to detect gross errors in modeling data for a propylene concentration soft sensor in a refinery factory and good results were obtained.
用该方法对某炼油厂的气体 分离装置的丙烯浓度软测量建模数据进行过失误差侦破，取得了很好的效果。
Secondly, the factors that influence the errors of the end-effector of the master-slave robot are analyzed, various error modeling methods of robot are compared.
其次，分析了影响主从机器人末端执行器的误差的因素，比较了各种机器人误差建模的方法。
At last, experiments are carried out in a water tank. Experimental results show that the beam-space MUSIC algorithm has high resolution ability and can bear preferably with array modeling errors.
进行了消声水池实验，结果表明波束域高分辨MUSIC法分辨力高，对阵列误差具有较大的宽容性。
We have studied the modeling technique and the regularity of the machining errors for multi-axis NC machine tools based on the analysis of their structures.
深入分析了多轴数控机床的结构特点，提出了基于多体系统理论的多轴数控机床描述方式。
Three-Layer Neural Network is used to compensate the modeling errors and a robust control is also designed to add the anti-interference ability of system.
该方案采用神经网络补偿系统中的非线性部分，设计了鲁棒项来增加系统的抗干扰能力。
Three-Layer Neural Network is used to compensate the modeling errors and a robust control is also designed to add the anti-interference ability of system.
该方案采用神经网络补偿系统中的非线性部分，设计了鲁棒项来增加系统的抗干扰能力。
应用推荐