This error voltage is known as contact potential or offset voltage.
该误差电压就是所谓的接触电势或偏移电压。
After this voltage was compared with REF, we can get the magnified error voltage.
将此电压与基准电压源(REF)进行比较，得到了被放大的误差电压。
Various errors of an operational amplifier can be substituted by equivalent error voltage or current sources.
运算放大器的各种误差都可以用等值的电压源或电流源来代替。
As shown in Figure 2-2, the input bias current (IBIAS) develops an error voltage across the source resistance (RS).
如图2 - 2所示，输入偏置电流(IBIAS)在源电阻(RS)上产生了误差电压。
Press source (ref) this voltage and the reference point to carry on the comparison, obtained the error voltage which enlarges.
将此电压与基准点压源(REF)进行比较，得到了被放大的误差电压。
This error voltage serves as is controls the electric charge pump breakover resistance (to call that it controls resistance pressure), then obtained a stable output voltage.
这个误差电压被用作是控制电荷泵导通电阻，进而获得了一个稳定的输出电压。
If the AC voltage at the input is large, part of this signal is rectified, producing an error in the DC signal being measured.
如果输入端的交流电压很大，其一部分信号被整流，于是在被测的直流信号中产生了误差。
Although input bias current is a common source of this type of error, currents generated by external circuits can also result in errors due to voltage drops across the source resistance.
虽然输入偏置电流是这种误差的常见来源，但是外电路产生的电流在源电阻上形成的电压降也能引起误差。
The offset voltage will cause an error in the applied stimulus to a device under test or the value measured by the voltmeter.
偏移电压会导致施加到被测装置的激励发生误差，或者使伏特计的测量值发生误差。
The metering error considers the non linear effect of the voltage coil and current coil in watt hour meter under different order of harmonics and different distortion degree of input waveform.
计量误差考虑了电度表电压线圈和电流线圈在不同的谐波次数以及谐波大小时的非线性效应。
Therefore, it's best to use the lowest possible voltage source range in order to minimize error.
所以，为了尽量降低误差，最好使用尽可能低的电压源量程。
However, a number of error sources in the circuit may be seen as a non-zero voltage offset.
然而，电路中的若干误差源可以引起非零的电压偏置量。
Leakage current is an error current that flows through insulators when a voltage is applied.
漏泄电流是在施加电压时通过绝缘的误差电流。
If the load resistor was connected directly across the voltmeter input terminals, the current through the relay contacts would cause a voltage drop and the measured cell voltage would be in error.
如果负载电阻被直接连接到伏特计的输入端子，通过继电器触点的电流会产生电压降，测得的电池电压将存在误差。
It also introduces the error values of shockproof test, harmonic test, voltage and temperature test.
介绍了电度表的耐振试验、谐波试验、电压和温度试验的误差数据。
This paper mainly studies the coupling error caused by induction voltage phase difference, and fluctuation of directional sensitivity caused by changes in near-field difference slope.
本文着重研究了因近场感应电压相位差引起的耦合误差，以及近场天线差斜率变化引起的定向灵敏度的变化；
The reason of nonlinear error caused by output voltage in common electric bridge as the sensor is analyzed.
分析了一般电桥电路作为传感器其输出电压产生非线性误差的原因。
The error tracking correction technique of digital disperse complex number voltage measure.
离散化的复数电压测量误差跟踪修正技术。
Using the characteristic of integrated operational amplifier, an electric bridge circuit sensor without nonlinear error in its output voltage is designed.
利用集成运算放大器的特点，设计了输出电压无非线性误差的电桥电路传感器。
By analyzing the error of parameters of Millikan oil drops experiment, the proper voltage and the proper time required for its falling through a specified distance are found.
通过对密立根油滴实验参数的误差分析，找出适当的平衡电压和下降一段距离所需要的时间。
Because the voltage measuring error increases when phase to phase short circuit occurs, distance relay protection will act improperly.
但是短线路在两相短路时，由于测量电压的误差会放大，可能引起距离保护的超越。
Aiming at the phase error of the electronic voltage transformer (EVT) with capacitive divider, a phase compensation scheme was proposed.
针对基于电容分压原理的电子式电压互感器的相位误差，提出了相位补偿方案。
Memory cell capacitance is the crucial parameter which determines the sensing signal voltage, speed, data retention times, endurance and against the soft error event.
记忆体电容是决定检测讯号电压、速度、资料保存时间、耐久性以及防止软性误差的重要参数。
Connected to the other input of the error amp is the midpoint of a voltage divider. We'll come back to this later.
连接误差放大器另一个输入点的是一个电压分压器的中点电压。稍后我们再来讨论。
When we measure the electric machines with little steady voltage adjusting rate, the absolute error of the voltmeter reaches out of the range of the steady state voltage adjusting.
在测量一些稳态电压调整率非常小的电机时，会出现测量用电压表的最大绝对误差大于稳态电压调整的范围。
With voltage measurements, the input current is ideally zero; thus, any input current represents an error.
对电压测量来说，理想的输入电流应为零，所以，一切输入电流都代表误差。
Some compensation data for nonlinear error in metrical system is normally acquired from the measurement of tested the standard voltage by external equipments.
有些用于补偿检测系统非线性误差的数据，通常是借助外接仪器测量待检品标准量电压的方法来获取的。
Low voltage Measurements: Discussion of potential error sources and how to minimize their impact on low voltage measurement accuracy.
低电压测量：讨论各种潜在的误差来源以及如何尽量降低它们对低电压测量的准确度的影响。
Low voltage Measurements: Discussion of potential error sources and how to minimize their impact on low voltage measurement accuracy.
低电压测量：讨论各种潜在的误差来源以及如何尽量降低它们对低电压测量的准确度的影响。
应用推荐