In adaptive optics system, the noise of wavefront sensor is a major error source.
在自适应光学系统中，波前探测器的噪声是一个主要误差源。
Anomalous refraction is believed to be the main error source for classical astrometry.
反常折射已成为传统天体测量学的主要误差来源。
As the main error source of SINS, the errors of inertial instrument must be compensated.
惯性元件误差是捷联惯导系统的主要误差源，必须在导航过程中加以补偿。
Firstly with microcosmic and macroscopic method, the error source in gear cutting is analysed.
首先以微观与宏观相结合的方法，分析了齿轮加工中的误差源。
The error source and feasibility of INSAR DEM construction on inland ice sheet is well analyzed.
深入分析内陆冰盖地区重复轨道INSAR测量地形的精度和可行性。
Besides standardization, zero correction error constitutes the most common error source of a gravimeter.
零位校正误差是重力仪除标定以外最主要的误差来源。
The radio refraction error is a main error source among the factors affecting the accuracy of the measured data.
电波折射误差是影响靶场测量数据质量的主要误差源之一。
The principle of measurement, it 's error source and treatment method have been analysed in detail in this article.
文章介绍了测量原理以及测量的误差来源及其处理方法。
Based on a detailed analysis of error source, some measures for increase of observation accuracy have been suggested.
并较详细地分析了误差来源，提出一些提高观测精度的措施。
The results show that gravity disturbance vector is a major error source for high accuracy inertial navigation system.
结果表明，不确定的重力扰动向量是高精度惯导系统的一个重要误差源。
This article has analyzed the error source of the thermocouple calibration system, and evaluated the error uncertainty.
本文分析了热电偶检定系统的误差来源，并对误差不确定度进行评定。
The key factor affected the application of wireless location system is the error source and the error mitigation method.
影响无线定位系统应用的关键因素是系统的误差源和误差抑制方法。
Determine the error source of the measurement system, and analyze the accuracy of the actual measurement result in theory.
确定测量系统的误差源，并从理论上对实际测量结果的精度进行分析。
This paper gives the research and the analysis about the error source and the erasing method of error on the grating angle sensor.
就光栅角度传感器的误差来源以及消除误差的措施进行分析和研究。
Existing phase extraction algorithms are just insensitive to specifically error source, and can't satisfy high precision optical testing.
现有的相位提取算法只对某些特定的误差不敏感，不能满足高精度光学检测的要求。
In sinusoidal phase modulating laser diode interferometer, the main error source is the variation in output light intensity of light source.
在半导体激光正弦相位调制干涉仪中，光源输出光强的变化是测量误差的主要来源。
The error source of the three-axis turntable is analyzed, which affect the precision of test of pendulous integrating gyro accelerometer (PIGA).
分析了三轴转台设备误差源；讨论了转台误差对陀螺加速度表测试精度的影响。
The major error source of GPS systems, especially of differential GPS, is the multipath signals. It will deteriorate the precision of positioning.
GPS测量，尤其是差分GPS测量，多径信号是主要的误差来源，会引起定位精确度的恶化。
The ionospheric delay error is a major error source which degrades the positioning accuracy in network real time kinematic (RTK) positioning over a long distance.
在长距离GPS实时动态定位(rtk)过程中，电离层延迟误差是影响定位精度的主要误差源。
In the application of vehicle navigation in city area, Multi-path errors are the main error source of GPS high-precision differential positioning in a near distance.
在城市车辆导航过程中，多径误差是近距离差分gps等高精度定位的主要误差源。
When 3-D measurement for large building is carried out, the parallel movement of laser and sensor is not needed, thus error source is reduced and accuracy is improved.
在进行建筑物等大目标三维测量时，不需激光器和传感器平行移动，减少误差来源，提高精度，方便可行。
The measurement error source of center of cone gravity, arithmetic and uncertainty of ATS are given, and the measurement accuracy of cone center of gravity is improved.
着重分析了锥体重心测量系统测量误差的来源、算法及系统整体测量不确定度的评定，从而可以提高锥体重心的测量准确度。
Firstly, the error source of baud rate and the allowable baud rate error are analyzed with the example of MCS-51. Then a method of baud rate autoregulation is presented.
首先以MCS - 51为例，分析了波特率的误差源和允许的波特率误差，然后介绍了一种自动调整波特率的方法。
The phase mismatch error is the main error source of sound intensity measurement system. It is difficult to eliminate this error only by upgrading the accuracy of instrument.
相位失配误差是声强测量系统的主要误差源，仅靠提高仪器的精度很难消除这一误差。
The fourth part is target validating and error analyzing, validating the target of the design and analyzing the possible error source which may effect the result of the experiment.
第四部分为设计指标验证及误差分析，详细验证了设计时提出的性能指标，并对可能影响到实验结果的误差来源进行了分析；
By analyzing each error source of checking device of USMT, the uncertainty of checking device of USMT is analyzed and calculated with mathematical statistics and experimental method.
通过对用电现场管理终端校验装置的各项误差源的分析，利用数理统计和实验方法对用电现场管理终端校验装置的不确定度进行分析和计算。
By analyzing each error source of checking device of USMT, the uncertainty of checking device of USMT is analyzed and calculated with mathematical statistics and experimental method.
通过对用电现场管理终端校验装置的各项误差源的分析，利用数理统计和实验方法对用电现场管理终端校验装置的不确定度进行分析和计算。
应用推荐