The test data needs to be reflective of application processing constraints as well as error and boundary conditions.
测试数据必须能够反映应用程序处理限制、错误和限制条件。
The Optim solutions support an iterative testing model that simplifies specification of error and boundary conditions and simplifies the comparison of test results to baseline data.
Optim解决方案支持迭代测试模型，该模型简化了错误和限制条件说明，以及测试结果与基线数据的对比。
The results of the test data indicate that the prediction system is reliable and the root of mean square error is about 15%.
对测试数据的预测结果表明，该预测系统能够可靠工作，预测结果的均方根误差在15%左右。
The method adopted computer to acquire autocollimation data and reduced test data error caused by manual record, so the veracity of test data was improved.
该方法由计算机自动采集自准直仪的数据，解决了以往人工记录引起的测量误差，提高了检测数据的准确性。
A significance test of parameters associated with a reasonable error analysis is used to judge the consistency of experimental data in different error grades.
一种参数的显著性检验方法，结合合理的误差分析，被用来对实验数据在不同误差等级下的一致性进行判断。
The measurement accuracy which is obtained through analysis and estimation of error in tests is the important basis for evaluating the reliability of test data.
测量精度是评价试验数据可靠性的重要依据。它是通过试验误差的分析和估算而得出的。
The test result also verifies the reasonable value of surface flux calculation, the conclusion can detect error in observed data.
试验结果也证实了表面通量计算的合理性，其结论可用于对实测资料进行误差检测。
Finally by measuring the diffraction intensity distribution of test system accuracy and stability, and give specific data and error analysis.
论文最后通过测量单缝衍射光强分布实验测试系统的精度和稳定性，并给出了具体的数据和误差分析。
The error compensation of test data is achieved with the least square method.
最后基于最小二乘法原理实现了测试数据的误差补偿。
Then a simulation of cycle discharge performance was carried out by using the cycle life test data got at high-temperature. The error of discharge voltage was less than 0.6%.
然后结合已有的高温循环寿命测试数据对电池循环放电性能进行了仿真，得到了放电电压误差不超过0.6%的结果；
It can work with high precision and low error for a long time, and has the function of real-time test, action edit and Data Processing.
它工作精度高，连续工作不产生累计误差，能实现动作编辑、实时检测、数据处理等功能。
This method can also be used for reliability test of observed values and for cancelling the influence of coarse error data.
用此方法还可以进行观测值的可靠性检验和粗差剔除。
The results of the test data indicate that the prediction system is reliable and the root of mean square error (RMSE) is about 15%.
对测试数据的预测结果表明，该预测系统能够可靠工作，预测结果的均方根 误差在 15%左右。
Because it is difficulty for estimating parameters of well and formation., it is different between design goal of well testing and results of test and results in interpretation error of data.
由于对油气井和地层参数估计困难，设计目标与实施结果可能存在较大的差异，导致测试资料的可解释性差。
The test data of bit error rate and signal-to-noise ratio show that the performance of the receiver terminal is available, which guarantees the accuracy of the data after the forward error correction.
从比特误码率、信噪比等测试结果数据分析可知，接收终端的性能合格，经过前向纠错后可以保证用户数据的准确性。
The method is employed to deal with a consolidation test data error, to show its effectiveness Results show that after treatment the precision of settlement analysis is higher than ever before.
实例应用结果表明，经光顺样条滤波处理后，能提高沉降数据分析的精度。
By analyzing of the test data, it shows that most of the data are within the range of the admissible error. That is to say this method is testified to be applicable in practice.
通过对实验数据的分析发现，大多数数据结果都在误差的允许范围之内，表明了这种方法具有一定的实用性。
In this paper, the sources of error in no-load engine power testing are analyzed. Two methods to reduce the errors are put forward, based on the investigation of actual test data.
分析了无外载测功法中的主要误差来源，在对实测数据分析研究的基础上，提出了两种提高精度的方法。
F test; t test)and estimation error of the model. Evaluating index for spatialised data products includes mean value, maximum value, value distribution range and spatial distribution of errors.
完整的属性数据空间化误差的评价指标包括数据源、空间化模型和数据产品等三个方面。
The error-delaying and data-switching and system-managing and anti-jamming of test system based on CAN bus instruments are better than the system based on traditional instruments.
基于CAN总线的测试系统在容错处理、数据交换、系统管理、抗环境干扰等方面都比传统仪表组成的系统功能强。
The error-delaying and data-switching and system-managing and anti-jamming of test system based on CAN bus instruments are better than the system based on traditional instruments.
基于CAN总线的测试系统在容错处理、数据交换、系统管理、抗环境干扰等方面都比传统仪表组成的系统功能强。
应用推荐